background image

FreshWater Salt System

 

                              

Page 3

English

be below 0.2 ppm. If metals are present in the water, they must be removed before startup 

of the FreshWater Salt System. It is strongly recommended to fill your spa using the 

FreshWater Clean Screen  Pre-Filter. FreshWater Stain and Scale Defense can also be 

used following instructions on the bottle.

IMPORTANT:

 If you use liquid products to remove metals from your spa water, you must 

clean your filters and wait 24 hours after treatment before turning the salt system on or 

adding any chlorine. See Treating for Metals on page 8.

Step 2 - Fill Spa 

NOTE: If you are performing a drain and refill of your spa, it is recommended to 

clean filters prior to filling the spa.
If you are changing your current water care program to FreshWater Salt System, you 

must drain and rinse your spa and clean your filters before proceeding.

Before adding water, remove plug and insert your salt system cartridge. Using your garden 

hose, fill your spa through the filter compartment until the water level reaches 1-inch (2.5 

cm) above the highest jet. 

NOTE:

 If your fill water contains high levels of metal (over 0.5 ppm) or calcium (over 300 

ppm), use the FreshWater Clean Screen Pre-Filter and/or On The Go as required. Calcium 

hardness should be between 25 - 75 ppm.
If you are using a FreshWater Mineral Spa Sanitizer cartridge with the FreshWater Salt 

System, insert into the filter compartment per packaging instructions. 

Silver Ions 

help 

to inhibit bacteria growth and will lower the amount of chlorine needed to keep the water 

clean. 

Once the spa is filled with water, turn the spa power on (see spa owner’s manual for 

specific instructions based on the voltage of your hot tub). Set the temperature to your 

desired level (at least 95 degrees Fahrenheit / 35 degrees Celsius). At initial start-up, it is 

recommended to set your output level to 0 (system off) until your spa water has reached 

temperature and salt has been added.
Check your jet systems by pushing the jets icon on the control panel home screen. When 

you’ve confirmed that the jets are fully operational, adjust your diverter valve to middle 

position and leave the jets on before adding salt.

NOTE:

 It’s normal for the water care icon on the control panel and diagnostic logo light (if 

equipped) to flash during this step if you choose not to turn your salt system off.

Step 3 - Add Salt 

(Target 1,750 ppm)

To find the correct water capacity of your spa model, check the chart in your spa owner’s 

manual.
Make sure spa jets are on before adding salt. To avoid over salting the water, start out by 

adding half the recommended amount of salt (Reference Table 1), using the cup provided 

with your FreshWater Spa Salt. Pour the salt into the filter compartment, 1 cup at a time, 

with the jets running. Allow five minutes for the salt to dissolve. 
Use FreshWater Salt Test Strips to verify the salt level is around 1,750 ppm. Continue to 

add salt, one cup at a time, as needed to reach the target level. Be careful to not exceed 

the maximum recommended level of 2000 ppm.

Summary of Contents for Freshwater Salt System























































Reviews: