Waterous Eclipse ES TC20 Operation And Maintenance Download Page 1

Read through the safety information and oper-
ating instructions carefully before using your 
Waterous Eclipse™ CAFSystem. 

 Table of Contents

 

Safety Information ........................................................ 2

 

General Description ..................................................... 3

 

Standard Items Furnished / Shipped Loose................... 4 

General Information ..................................................... 5

 

Auto Sync Control Panel ................................................ 5 

Unload / Fixed / Auto Control Valve ............................ 

CAFS Nozzle / Flow Rate / Hose Combinations ............ 5 

Nozzles

 ....................................................................... 5 

Foam Concentrate Ratios

 ........................................... 

5

 

Hose

 ............................................................................ 5 

Operation ...................................................................... 6

 

Water Pumping Operations ............................................ 6 

Advantus Foam Operation (Optional) ............................ 6 

Foam Solution Operations ............................................. 7 

Compressed Air Foam Operations ................................ 8 

Compressed Air Only ..................................................... 8 

Shut Down Procedure.................................................. 9

 

Compressed Air Foam Operations ................................ 9 

Compressed Auto Shut Down .................................... 9

 

Service and Maintenance ............................................ 9

 

Poly Chain Replacement and Adjustment ............... 10

 

Calibration - Control Air Circuit ................................ 12

 

Troubleshooting Guide.............................................. 13

 

Control Air Circuit Function ...................................... 16

 

 
 

 

 

 

Eclipse ES CAFSystem Operation and Maintenance Instructions 

All content in this instruction is property of the Waterous Company.   Instructions subject to change without notice.

Waterous Company  125 Hardman Avenue South, South St. Paul, Minnesota  55075  USA  (651) 450-5000

Instructions subject to change without notice.

Visit us at www.waterousco.com

Eclipse ES Op-
eration & 
Maintenance 

Eclipse ES CAFSystem 

Eclipse ES CAFSystem   

  Operation and Maintenance    

Form No.

F-1031 

Section

2119 

Issue Date

04/07/03 

Rev. Date 

10/17/18 

Summary of Contents for Eclipse ES TC20

























Reviews: