background image

 

 

Read through the safety information and 
overhaul instructions carefully before repair-
ing your Waterous CPK-5 Series Fire Pump. 

               

      Table of Contents

 

 

Safety Information ................................................................................... 2

 

Introduction .............................................................................................. 3

 

General Description ................................................................................. 3

 

General Overhaul Information ................................................................ 3

 

Tools and Equipment .............................................................................. 3

 

Preliminary Testing ................................................................................. 3

 

Cleaning ................................................................................................... 3

 

Pump Bodies and Impellers ....................................................................... 3 

Bearings, Gaskets, Seals and O-rings ....................................................... 4 

Impeller Shafts ........................................................................................... 4 

Installing Ball Bearings .............................................................................. 4 

Installing Body Gaskets ............................................................................. 4 

Disassembly

 ........................................................................................ 4 - 5 

Reassembly

 .............................................................................................. 6 

Testing

 ...................................................................................................... 7 

Hydrostatic Testing .................................................................................... 7 

Operational Testing ................................................................................... 7 

NOTE: Instructions subject to change without notice 

Waterous Company, 125 Hardman Avenue South, South St. Paul, Minnesota  55075  USA  (651) 450-5000

 

www.waterousco.com 

F-1031, Section 5015 (Issued: 05/17) 

 

CPK-5 Series Fire Pumps  

Overhaul Instructions 

 

   

 

Summary of Contents for CPK-5 Series








Reviews: