background image

|

 28

Safety

Introduction

Product Overview

Operation

Maintenance

Safety Precautions

• 

Read and understand all the associated documentation before you begin 

operating the product.

• 

Contact Waterous when you have questions about operating or maintaining 

the equipment.

NOTICE

Before Operation

• Read and understand all

  the instructions provided.

• Check all fluid levels

  and replenish if necessary.

• Remove all shipping plugs

  and install the operation

  plugs or caps.

NOTICE

Pump Damage

• Pump damage occurs

when operating without

adequate water supply.

• Do not operate the pump

without adequate water

supply.

• 

Read and understand all the notices and safety precautions.

• 

Do not operate the equipment when safety guards are removed.

• 

Do not modify the equipment.

NOTICE

• Do not allow fluid in the

lines to freeze.

• Remove all freezable fluid

from the lines before

storing the apparatus.

Freeze Damage

NOTICE

Pump Damage

• Storing the pump partially

   full causes undesirable

   corrosion.
• Always store the pump

  completely full or empty.

Summary of Contents for CM Series





























Reviews: