WaterLogic CUBE FIREWALL Manual Download

Page: 62 / 85

CUBE

Manual

Page 62 - Revision: 5-24-2017

Leak Detection Icon Flashing

Most leaks will be detected by either the internal leak detection system that will trigger an alarm, or will

trip the Waterlogic block located in the installation kit.

Solution

Turn off both the Green Heater/Compressor Switch and Red Power Switch. O = OFF

Unplug unit.

Remove Top Cover.

Remove Right Side Panel (Left Side Panel if standing behind unit).

Dry inside of the CUBE.

Replace Top Cover (leave Side Panel off).

Connect power cord.

Turn on Red Power Switch I = ON

Dispense water and check for leak.

10.

Once leak is located, correct issue.

11.

Remove Top Cover.

12.

Replace Side Panel.

13.

Replace Top Cover.

14.

Turn on Green Heater/Compressor Switch. I = ON

Leak Detection Indicator

Summary of Contents for CUBE FIREWALL






















































































Search results

Summary of Contents for CUBE FIREWALL

Reviews:

Related manuals for CUBE FIREWALL

Brands by name

Popular brands

WaterLogic CUBE FIREWALL, Manual

Search results

Summary of Contents for CUBE FIREWALL

Reviews:

Related manuals for CUBE FIREWALL

Brands by name

Popular brands