Waterco ELECTROCHLOR PLUS Owner'S Manual Download Page 1

Page: 1 / 12

WARNING

(W99368) 09/2018

www.waterco.com

Waterco Limited ABN 62 002 070 733

Owner's Manual

ELECTROCHLOR

Mineral Chlorinator PLUS

This equipment must be installed and serviced by a qualified technician.
Improper installation can create electrical hazards which could result in

property damage, serious injury or death. Improper installation will void the
warranty.

Notice to Installer

This manual contains important information about the installation, operation
and safe use of this product. Once the product has been installed

this manual

must be given to the owner/operator of this equipment

OFFICES – AUSTRALIA

NSW - SydNey
(HeAd OFFICe)

Tel

: +61 2 9898 8600

VIC/TAS - MelbOurNe

Tel

: +61 3 9764 1211

WA - PerTH

Tel

: +61 8 9273 1900

Qld - brISbANe

Tel

: +61 7 3299 9900

SA/NT - AdelAIde

Tel

: +61 8 8244 6000

ACT dISTrIbuTOr

Tel

: +61 2 6280 6476

OFFICES – OVERSEAS

WATerCO (eurOPe) lIMITed

Sittingbourne, Kent, uK
Tel

: +44 (0) 1795 521 733

WATerCO uSA

Augusta, uSA
Tel

: +1 706 793 7291

WATerCO CANAdA

boucherville, QC, Canada
Tel

: +1 450 748 1421

WATerCO (NZ) lIMITed

Auckland, New Zealand
Tel

: +64 9 525 7570

WATerCO (C) lIMITed

Guangzhou, China
Tel

: +8620 3222 2180

WATerCO (FAr eAST) SdN bHd

Selangor, Malaysia
Tel

: +60 3 6145 6000

PT WATerCO INdONeSIA

Jakarta, Indonesia
Tel

: +62 21 4585 1481

WATerCO SINGAPOre INTl PTe lTd
Nehsons building, Singapore
Tel

+65 6344 2378

Summary of Contents for ELECTROCHLOR PLUS













Search results

Summary of Contents for ELECTROCHLOR PLUS

Reviews:

Related manuals for ELECTROCHLOR PLUS

Brands by name

Popular brands

Waterco ELECTROCHLOR PLUS, Owner'S Manual

Search results

Summary of Contents for ELECTROCHLOR PLUS

Reviews:

Related manuals for ELECTROCHLOR PLUS

Brands by name

Popular brands