background image

Self Diagnostics

The Bar Graph and 

“ F ”

 symbol indicates the following conditions:

• 

F0

 - The salt level may have fallen below the required level. 

• 

F0

 - There is too much calcification on the salt cell plates for 

programmed chlorine production level.

• 

F0

 - The pool water temperature is lower than 15° C. 

• 

F1

 – When the current can only reach 50% of set chlorine production level. 

This condition indicates that one SCR (Silicon-Controlled Rectifier ) is not working.

• 

F2

 – The salt cell requires replacement.

• 

FL

 –

 No flow of water is present in the salt cell or a sensor wire has broken or the 

pump is not working or connected.

Note:  The  microprocessor  on  the  chlorinator  will  hold  its  memory  if  there  is  a  power 

interruption, ensuring that when it is turned on again, the operating sequence of the reverse 

cycle is maintained.

Time Clock Operation

When the Electrochlor is set to 

TIMER

, the timer 

will activate both the pump and chlorinator, 

as programmed.

Setting the Time Clock

Press and hold 

PROG

 key for 5 seconds, the day 

and time displays will start blinking. Let go of the 

PROG

 key and program vie the 

UP

 or 

Down

 keys.

The “day” will blink  

-->  

Press UP

 or 

Down

 keys to set 

-->  

ENTER

 to confirm.

The “hour” digit will blink 

-->  

Press UP

 or 

Down

 keys to set 

-->  

ENTER

 to confirm.

The “minute” digit will blink  -->  

Press UP

 or 

Down

 keys to set 

-->  

ENTER

 to confirm.

Setting Filtration / Chlorinator Times

Press 

PROG

 key once and release and the 

“ 123 

 will flash on the display to indicate 3 available 

programming periods for filtration/chlorination times. 

Use 

UP

 or 

DOWN

 keys to select either 

1, 2

 or 

3

 then 

press the 

ENTER

 key. 

The day and 

ON

 displays will start blinking. Use 

UP

 or 

DOWN

 keys to select the 

day, week days, week end

 

or 

ALL days

 then press the 

ENTER

 key to confirm. 

Next set the set the start time and finish time.

Summary of Contents for 25A













Reviews: