background image

I pg 09

Waterco Electrochlor LCD Chlorinators

General Safety Rules

1.  The equipment mentioned in this manual is specially designed for the sanitizing of water in

swimming pools.

2.  It is designed to work with clean water at a temperature not exceeding 35°C (95°F). 

3.  The installation should be carried out in accordance to the safety instructions of swimming pools

especially Standard HD 384.7.702 and the specific instructions for each facility.

4.  The rules enforced on accident prevention should be carefully followed.

5.  Any modification of the chlorinator requires the prior consent of the manufacturer.  Original

replacement parts and accessories authorized by the manufacturer ensure a high level of safety. 

The  manufacturer  accepts  no  liability  for  the  damage  and  injuries  caused  by  unauthorized 

replacement parts and accessories.

6.  During operation, some parts of the chlorinator are subject to dangerous electric voltage. Work

may only be performed on the chlorinator or on the equipment connected to it after disconnecting 

them and the starting device from the mains power.

7.  The user should make sure that assembly and maintenance tasks are carried out by qualified

authorized persons and that these persons have first carefully read the Service and Installation 

Instructions.

8.  The operating safety of the chlorinator is only guaranteed if the Installation and Service

instructions are correctly followed.

9.  The limit values stated in the Technical Specifications should not be exceeded under any

circumstance.

10.  In the event of defective operation or fault, contact the manufacturer’s Technical Support

Department or it’s nearest Authorized Agent.

11.  If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or

a similarly qualified person.

12.  This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for 

their safety.

These chlorinators are approved and conformed to AS3136 Swimming Pool Equipment, as a

prescribed article under Australian Registration.

These chlorinators conform to the Australian Electromagnetic Compatibility Standard marked by

the C-tick.

Summary of Contents for 25A













Reviews: