background image

Introduction

This manual explains the installation and maintenance instructions for the water Factory Systems’

N4000, N54500, N5000 Series Reverse Osmosis (RO) Drinking Water Appliances. Please read each section
of this manual carefully. The specific model chosen should be appropriate for the local water conditions and
the customer’s needs. Check the Performance Data Sheet which specifies performance characteristics and
the conditions of use.

The Water Factory Systems’ undercounter RO drinking water appliances are designed to connect per-

manently to a home plumbing system. To ensure the installation conforms to your state and local plumbing
codes, it is recommended that the installation be performed by a qualified specialist for RO drinking water
appliances or a licensed plumber. Failure to install as instructed will VOID the warranty.

Caution: The RO membrane cartridge is shipped with a preservative solution inside. Make sure to
flush it thoroughly as directed before first use. 

Table Of Contents

Installation Instructions

A.

Determine the appliance location

B.

Prepare the area for installation

C.

Prepare the appliance for installation

D.

Install the feed water valve and tubing

E.

Prefill and sanitize the storage tank

F

. Install the drain connection

G.

Install the faucet

H.

Make the faucet mounting hole

I.

Mount the faucet

J.

Make initial tubing connections

K.

Install purification assembly and storage tank

L.

Make final tubing connections

M.

Install the icemaker hookup (optional)

N.

Start up the system

O.

Flush system of preservative and check operation

P.

Cleanup, paperwork, and customer orientation

Appendix for basement installations
Installation troubleshooting
Installation diagrams, (Figures 1-6)

Operation & Maintenance Instructions

Important water quality assurance requirements
Replacing the filter cartridges
Replacing the RO membrane cartridge
Sanitizing the RO appliance

© 1995, CUNO/Water Factory Systems. All material herein may not be produced or copied in any manner without the expresse written consent of the publisher.

2

Summary of Contents for N4000 Series
















Reviews: