Water Factory Systems 40T Owner'S Manual Download Page 12

6) Twist the filter cartridge 1/4 turn to the left so that the ears on the cartridge are able to disengage from 

the head. Then, hold the head bracket with one hand while gently pulling the cartridge away from the 
head. (It may be necessary to move the cartridge slightly from side to side to help free it.)

7) Remove new cartridge from its sanitary sealed wrapper.
8) Using tap water, wet the o-ring seals to make insertion easier. Slide the filter cartridge under the 

retaining clip as shown in the drawing.

9) Line up the ears, insert the cartridge, and push into head until fully seated. Twist the cartridge 1/4 

turn to the right to lock into place.

10) Follow the same procedure as above for all filter cartridges.
11) Wipe any excess water from inside the base.
12) Carefully lift shroud and fit over base, making sure not to kink or twist tubing.
13) Holding both the base and the shroud together, turn the appliance upside down.
14) Using both hands, tighten the two base screw knobs by turning to the right at the same time.
15) Turn the appliance right side up.
16) Discard the first reservoir of water.

RO Membrane Cartridge Replacement

1) Remove tubing from the “Push-In” fitting at the bottom of the RO membrane cartridge. 

Note:

It may 

be helpful to remove the adjacent filter cartridge to make access easier.

2) Follow steps 6-9 from the section “Filter Cartridge Replacement Procedure” to replace cartridge.
3) Reconnect black tubing by inserting into the “Push-In” fitting at the bottom of the new RO membrane 

cartridge 

as far as it will go.

4) Wipe up any excess water from inside the base.
5) Follow steps 11-15 from the section “Filter Cartridge Replacement Procedure” for reassembling unit.
6) Allow the new membrane to flush for 24 hours prior to use.

Air Filter Replacement

1) Remove reservoir lid.
2) With clean hands, push out white disc and two black discs from bottom. Do not lose the plastic air 

filter cap on the opposite side.

3) Remove replacement discs from bag. FROM THE TOP, press white then black discs into receptacle.
4) Firmly press air filter cap into place.

11

Summary of Contents for 40T

















Reviews: