Wasp WPL206 Series User Manual Download Page 36 | Manualshive

Page: 36 / 46

background image

- 30 -

5.3

Setting Ethernet by Diagnostic Tool (Option)

The Diagnostic Utility is enclosed in the CD disk \Utilities directory or can be downloaded from

www.waspbarcode.com

website. Users can use Diagnostic Tool to setup the Ethernet by USB and

Ethernet interfaces. The following contents will instruct users how to configure the Ethernet by these

interfaces.

5.3.1

Using USB interface to setup Ethernet interface

1. Connect the USB cable between the computer and the printer.

2. Turn on the printer power.

3. Start the Diagnostic Utility by double clicking on the

icon.

4. The Diagnostic Utility default interface setting is USB interface. If USB interface is connected with printer,

no other settings need to be changed in the interface field.

5. Click on the “Ethernet Setup” button from “Printer Function” group in Printer Configuration tab to setup the

IP address, subnet mask and gateway for the on board Ethernet.

«
...
34
35
36
37
38
...
»

Summary of Contents for WPL206 Series















































Reviews:

No comments

Related manuals for WPL206 Series

Brand: MakerBot Pages: 48

Brand: Canon Pages: 797

LASER CLASS 730i

Brand: Canon Pages: 155

Brand: SEH Pages: 20

Brand: Olivetti Pages: 139

Brand: Lanier Pages: 234

Stacker 701P98048

Brand: Xerox Pages: 16

Brand: WANHAO Pages: 25

Brand: Ricoh Pages: 301

Brand: Tandy Pages: 83

Brand: Magicard Pages: 31

Brand: Ricoh Pages: 849

Brand: Ocom Pages: 23

Brand: Xerox Pages: 342

Brand: Canon Pages: 8

Brand: Canon Pages: 58

Brand: Canon Pages: 110

MultiPASS MP360

Brand: Canon Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands