Wasp WPL206 Series User Manual Download Page 16 | Manualshive

Page: 16 / 46

background image

- 10 -

3. Setup

3.1 Setting up the Printer

1. Place the printer on a flat, secure

surface.

2. Make sure the power switch is off.
3. Connect the printer to the computer

with the provided USB cable.

4.

Plug the power cord into the AC

power cord socket at the rear of the
printer, and then plug the power cord
into a properly grounded power
outlet.

Note:

* Please switch OFF (O) printer power switch prior to plug in the power cord to printer power

jack.

* The interface picture here is for reference only. Please refer to the product specification for

the interfaces availability.

«
...
14
15
16
17
18
...
»

Summary of Contents for WPL206 Series















































Reviews:

No comments

Related manuals for WPL206 Series

Brand: Keeler Pages: 25

Brand: Z Corporation Pages: 76

WorkCentre Pro 40

Brand: Xerox Pages: 14

Brand: Magicard Pages: 2

Brand: Magicard Pages: 2

Brand: BIXOLON Pages: 31

Brand: Kyocera Mita Pages: 209

Brand: OmniPrint Pages: 44

Brand: Oki Pages: 198

Brand: SEWOO Pages: 13

Brand: UEi Pages: 4

Brand: Felix Storch Pages: 46

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

Brand: Sagem Pages: 102

VarioPrint 4110

Brand: Oce Pages: 216

Brand: UVP Pages: 22

Brand: Shandong New Beiyang Information Technology Co. Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands