For mounting your new MOD V2 onto a
RockBoard®
pedalboard, there are multiple options. You can either mount it in its MOD slot (available on all
RockBoard®
pedalboards except
DUO 2.0 and 2.1) or detach the MOD’s front plate and mount it on top or underneath your 3rd party pedalboard.
MOUNTING ON A ROCKBOARD® PEDALBOARD
Please follow the below steps to mount your MOD V2 in the MOD slot of your
RockBoard®
pedalboard.
Prepare the pedalboard before you place your MOD in the RockBoard®’s MOD slot:
MOUNTING ON A NON-ROCKBOARD® PEDALBOARD
There are multiple ways of mounting your MOD on a non-
RockBoard®
pedalboard. You can either mount it directly to the board surface using hook & loop tape or another recloseable
fastener. Additionally
RockBoard®
offers the MOD Rack for mounting your MOD in various ways onto, into or underneath pedalboards of other manufacturers. For mounting your MOD
using the
RockBoard®
MOD Rack, please refer to the MOD RACK manual. Please follow the below steps to mount your MOD V2 in the MOD slot of your non-
RockBoard®
pedalboard.
STEP 1
Remove the rubber frame of your
RockBoard®
’s MOD slot.
STEP 2
Turn the
RockBoard®
pedalboard upside
down.
STEP 3
The MOD mounting screws are self-
tapping, they will cut their own threads
into the pre-drilled mounting holes
in the
RockBoard®
’s front. Use a TX10
screwdriver to screw the mounting
screws in and cut the threads. Should
you do not possess a TX10 screwdriver,
a wrench is included with the MOD. For
the first couple of rotations the screws will be hard-going, as they have to cut the threads
into the surrounding material. Please be careful not to screw them in at an angle.
STEP 4
Once the tips of the screws are sticking
out on the other side of the holes and the
screws become easier to turn, the threads
have been cut properly. Now remove the
screws again.
Now it‘s time to to load the MOD:
STEP 5
Next, load your chosen MOD from the
front into the slot and screw in the
mounting screws until the MOD’s front
plate sits flush with the face of the board.
STEP 6
For added security, you screw on the
counter nut on the back. Now the MOD
is ready to be connected with your
setup! Should you have difficulties
to reach the screws from behind to
screw on the nuts, you can take out the
additional support brace in order to
have space using. Please use the 3 mm
hex key wrench included with the
RockBoard®
pedalboard.
DETACHING THE MOD V2’S FRONT PLATE
For mounting the MOD V2 All-in-One Patchbays on top or underneath your pedalboard, you will have to detatch the Front plate, so it will fit flush onto/under the board surface. Remove the
screws as indicated below to release the front plate from your MOD V2 using a PH2 Phillips head screw driver. The mounting nuts of the jack sockets do not have to be removed!
STEP 1
Release the MOD’s front plate by
removing the screws indicated above.
STEP 3
Apply self-adhesive loop tape or another
recloseable fastener to the position of on
or underneath your pedalboard where
you want to place your MOD V2.
STEP 2
Apply self-adhesive hook tape or
another recloseable fastener to the
underside of the MOD housing.
STEP 4
Bring the two sides of hook & loop tape
or your other reclosable together attach
your MOD. Now the MOD is ready to be
connected with your setup!
MOD 1 V2
MOD 2 V2
MOD 3 V2
USA DISTRIBUTION: W-Music Distribution USA | [email protected] | 629.202.6790
CHINESE DISTRIBUTION: Warwick Music Equipment Trading (Shanghai) Co. Ltd. | [email protected] | +862134060110
NORTH EUROPEAN DISTRIBUTION: W-Music Distribution | www.w-distribution.de | [email protected]
Headquarters: Warwick GmbH & Co. Music Equipment KG | 08258 Markneukirchen / Germany | +49 (0) 37422 / 555 - 0
Family Owned • Solar Powered • Sustainably Manufactured in a Green Environment
Note: The manufacturer reserves the right to change these specifications without notice.
