background image

11. Remote Switch: The Power switch leads have a dual switch for powering in or 

powering out your winch drum. The remote control allows you to stand clear of 

the wire rope when the winch is under load. 

12. Universal  Flat  Bed  Mounting  Channel:  Your  winch  could  have  been  optionally 

supplied  with  a  flat  bed  mounting  channel  that  can  be  mounted  to  most  flat 

surfaces such as trailers, step bumpers, truck beds, etc. The mounting channel 

also has holes to accept your roller fairlead. 

13. Snatch Block: If your winch is supplied with a snatch block that can double the 

pulling power of the winch, or change the pulling direction without damaging the 

wire rope. We recommend you to use double line and snatch block for pulling 

over 70% of the rated line pull. 

SAFETY PRECAUTIONS 

WARNING

 

WARNING 

 

Do not exceed rated capacity shown in this table. 

 

Layer 

Rated line pull lbs (kgs) 

Total rope on the drum ft (m) 

4500(2041) 

7.6(2.3) 

3642(1652) 

17.0(5.2) 

3060(1388) 

27.0(8.3) 

2638(1196) 

38.6(11.8) 

2254(1023) 

47.6(14.5) 

 

WARNING 

 Intermittent use only.  Allow winch to cool between uses.

 

WARNING 

 

 Do not use winch to lift (vertically).

 

WARNING 

 

  Do not use winch to pull or move people in any way.

 

WARNING 

 

NEVER cut, weld or modify any part of the winch or cable.

 

WARNING 

 

A  minimum  of  five  wraps  of  cable  around  the  drum  barrel  is 

necessary for pulling and holding the rated load.  

WARNING 

 

Keep yourself and others a safe distance to the side of the cable 

when it is under tension.

 

Summary of Contents for 45SPA12




















Reviews: