background image

GETTING TO KNOW YOUR WINCH 

Your  9500lb  winch  is  a  powerful  piece  of  machinery.  It  is  important 

that you understand the basics of its operation and specifications so that 

when  you  need  to  use  it,  you  can  use  it  with  confidence  and  safety. 

Below is a list  of  the  components  of  your  winch  and  their  use.  Practices 

using  your winch before you are in a situation to need to use it. 

1.

Motor:  Your  5.5/8.3hp  motor  is  powered  by  a  12/24  volt  battery  and  provides

 

power to the gear mechanism which turns the drum and winds the wire rope;

2.

Winch Drum: The winch drum is the cylinder on which the wire rope is stored. It

 

can feed or wind the rope depending on the remote winch switch.

3.

Wire  Rope:  Your  winch  has  a  3/8"X85' galvanized  aircraft  cable  designed

 

specifically for load capacity of 9500lbs. The wire rope feeds  onto the drum in

 

the “under wind” position through the roller fairlead and is looped at the end to

 

accept the clevis hook pin.

4.

Roller  Fairlead:  When  using  the  winch  at  an  angle  the  roller  fairlead  acts  to

 

guide the wire rope onto the drum and minimizes damage to the wire rope from

 

abrasion on the winch mount or bumper.

5.

Mechanic  Gear  System:  The  reduction  gears  convert  the  winch  motor  power

 

into extreme pulling forces.

6.

Braking  System:  Braking  action  is  automatically  applied  to  the  winch  drum

 

when  the  winch  motor  is  stopped  and  there  is  a  load  on  the  wire  rope.  The

 

braking action is applied by a separate  mechanical brake.

7.

Free  Spooling  Clutch:  The  clutch  allows  the  operator  to  manually  disengage

 

(“Out”)  the  spooling  drum  from  the  gear  train,  free  spool.  Engaging  the  clutch

 

(“In”) locks the winch into the gear system.

8.

Solenoid:  Power  from  the  vehicle  battery  flows  through  the  weather  sealed

 

switch before being directed to the winch motor.

9.

Remote  Switch:   The  Power  switch  lead  has  a  dual  switch  for  powering  in  or

 

powering out your winch drum. The Power switch leads allow you to stand clear

 

of the wire rope when the winch is under load.

10.

 Wireless Remote Control: allow you control winch far from 50 Ft away. 

Summary of Contents for S9500HS

















Reviews: