background image

WINCH MANUAL 

WARRANTY*

14

WARRANTY*

 BPE Solutions North America are the sole distributors of these 

WARRIOR HOISTS and associated brands/equipment.

BPE Solutions North America (“seller” or BPE) warrants to the original 

retail buyer only (“Buyer”) that any mechanical component of this genuine 

hoist (“product(s)”) are free of defects in material and workmanship for 

the lifetime of the hoist.

The electrical components (including the motor, contactor, and switches) 

will be free of defects in material and workmanship for a period of (3) three 

years (36 Months) from the original purchase provable date of purchase

Any product BPE Solutions North America determines to be defective 

will be repaired or replaced at our (BPE Solutions North America) sole 

discretion without charge to the Buyer upon Buyer’s compliance with 

this procedure. Seller or its Authorized Agent may make reasonable 

charges for parts and(or) labor for repairs not covered by this Lifetime 

Limited Warranty. None warrantable returns will be charged at BPE 

Solutions North America standard rates. The warranties set forth herein 

are exclusive and in lieu of all other warranties, whether oral or written, 

express or implied. 

If in the event your product becomes faulty 

within your warranty period

To obtain service or repair under this warranty, the Buyer shall mail, ship 

or otherwise deliver to the manufacturers address, at the Buyers expense; 

(1) the Product, (2) a written description of the problem, (3) Buyers name, 

address and contact number, (4) copy of the original purchase receipt or 

BPE Solutions North America can arrange a suitable collection method 

(Charges apply).

Warranty Exclusions

The Warranty does not cover the cost of labor or transportation/shipping 

charges for the replacement or installation of defective part(s).
This warranty does not apply to defects of the Product caused by; 

(1) normal wear and tear, (2) failure to comply with any installation, 

maintenance or subjecting the product to loads in excess of the loads 

written/listed in the owners manual or as detailed upon the Sellers 

website, (3) alteration or modification by any parties other than the 

manufacturer, (4) misuse, abuse, neglect, accidents, Acts of God, 

terrorism or (5) failure to correctly use the item according to the owners 

manual (7) other causes beyond the control of the Seller after delivery of 

the Product to the Sellers Authorized Agent.

Other Exclusions

This Warranty does not cover steel cables, synthetic ropes, fairleads, 

wireless remotes or any exterior finishes outside thirty (30) Days from 

purchase.

BPE Solutions North America shall not be responsible or liable for any 

indirect or consequential damages. These consequential damages may 

include, but are not limited to, lost profits or loss of use, down time or 

damage to other person(s) equipment.

BPE Solutions North America reserves the right to change the Product 

design without notice. BPE Solutions North America reserves the right to 

replace any part or whole unit with a newer design of the same function.

Summary of Contents for EH800-CAD











































Reviews: