manualshive.com logo in svg

Warn A2000, Service Manual

Share
Download
Warn A2000 Service Manual Download Page 24

24 

 

Motor Cable (#1) 

 

 

Motor Cable (#2) 

 

 

Control Pack Ground Cable  

 

 

Positive Battery Cable 

 

 

Diode 

 

 

 

 

Figure 4.3 Solenoid Control Pack and Wiring Connections 

 
 

4.1.4 Solenoid Control Pack(Pull Pack)-

 

This solenoid pack contains 2 canister 

solenoids, a diode, and one electrical cable which will run under the winch motor and connect to terminal 
#2. Motor terminal #1 will connect to short copper angle bracket. Diode will connect to top solenoid, 
grounding back to solenoid fastener, attached with screw through plate and fastener.  This screw must be 
snug for grounding purposes. 

 

 
 

Figure 4.4 is the basic wiring diagram of the ATV Pull Pack solenoid control pack .

  

 

 

Diode 

 

 

Control Pack Ground Cable 

 

 

Motor Cable (#2) 

 

 

Motor Cable (#1) 

 

 

Positive Battery Cable 

 

 

Remote Socket Wiring 

 

Figure 4.4 Solenoid Control Pack and Wiring connections 

 
 
 

Summary of Contents for A2000














































Reviews:

No comments

Brands by name

Popular brands

Load more brands