background image

WARN INDUSTRIES 

PAGE 1 

39527 Rev A1 

 

   

 
 

 
INSTALLATION INSTRUCTIONS

 

ATV SNOW PLOW

 

Mounting Kit:  PN 37851 
Application: HONDA 400 

 

 

 
 

 

WARNING

 

SEVERE INJURY OR DEATH MAY RESULT IF YOU IGNORE ANY OF THE 
FOLLOWING.

 

 

Read the Plow Operator’s Manual, the Winch Operator’s Manual, and all warning 
labels before operating. 

 

Operate ATV at a walking speed with the blade installed.  Do Not exceed 5mph       
(8 km/h) even with the blade up. 

 

Plow Cautiously, impact with a hidden or stationary object may cause the ATV to 
stop suddenly or go out of control. 

 

Do Not operate the ATV on slopes greater than 10° with the plow installed. 

 

Do Not stand or ride on the plow. 

 

Stay clear of moving parts and joints.  Keep others away when operating or 
adjusting plow. 

 

Inspect the plow mechanism, fasteners, cable, and adjustments before operating.  
Replace all worn or damaged parts before operating. 

 

Lower the plow to the down position before leaving the ATV unattended.

 

 

TOOLS REQUIRED:

 

 

Ratchet 

Sockets: 7/16, 1/2, 9/16” 

Wrenches: 7/16, 1/2, 9/16” 

Phillips Screwdriver (optional) 

 

 

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided 
installation and operating instructions and other information on labels and in this guide. This information alerts you to potential 
hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must 
use your own good judgment.

  

CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY OR EQUIPMENT DAMAGE. 
READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS BEFORE INSTALLING 
AND OPERATING THIS PRODUCT. 

This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury or death. 

WARNING

 and 

CAUTION

 are signal words that identify the level of hazard. These signal words mean:  

 WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations. 

CAUTION signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.

  

This guide uses 

NOTICE

 to call attention to important mechanical information, and 

Note:

 to emphasize general information worthy of 

special attention. 

Summary of Contents for 37851






Reviews: