background image

The world’s 

best-selling electric floor heating brand

The world’s 

best-selling electric floor heating brand

WARMUP INC. 

USA: [email protected]
Tel.: 1-888-927-6333 
www.warmup.com

CANADA: [email protected] 
Tel.: 1-888-592-7687
www.warmup.ca

DS-2C RAIN/SNOW SENSOR CONTROLLER
INSTALLATION INSTRUCTIONS

CAUTION: Read all instructions carefully before installation. 
Save this Installation Manual for future reference.

GENERAL SAFETY INSTRUCTIONS

1.  THIS UNIT SHOULD BE INSTALLED, OPENED AND REPAIRED BY QUALIFIED 

PERSONNEL ONLY!

2.  To avoid shock hazard do not open the front cover with power 

connected to the DS-2C or any controlled equipment.

SELECTING A MOUNTING LOCATION FOR THE DS-2C

The interleaved grid on the top of the DS-2C is the precipitation or “moisture” sensor. The brass cylinder 

protruding from the bottom of the enclosure is the temperature sensor. For reliable rain and snow detection 

the unit must be mounted in a location that exposes the moisture sensor to a clear view of the sky.

The unit should not be mounted directly under eaves or overhangs. It should not be mounted so close to the 

ground that it may become buried in snow. For proper temperature detection the DS-2C must be mounted 

outdoors, away from furnace vents, dryer vents, and other sources of heat. Note that, when powered, the 

DS-2C moisture grid will always remain hot. This is normal. This allows the sensor to continuously melt 

snow and evaporate both rain and snow from the grid.

The DS-2C can be mounted by screwing 

the base conduit hub onto an appropriate 

size free-standing conduit or by using 

the mounting holes in each corner of the 

enclosure. 

DO NOT DRILL HOLES THROUGH THE 

ENCLOSURE FOR MOUNTING! 

This can allow 

water into the enclosure causing a potential 

shock hazard. It is recommended that a 

weatherproof junction box be mounted 

below the DS-2C for termination of the power 

and load pigtails to the building wiring.

Use Care When Replacing the Front Cover. Do Not Pinch the Gasket or Overtighten the Screws.

ALWAYS FOLLOW LOCAL AND NATIONAL ELECTRICAL CODES.

Summary of Contents for DS-2C







Reviews: