background image

 

Instructions condensing  Air heaters type XR version XR-GB-4001-a 

 

 

 

 

Page 4/25 

2.2.4 Protection from water and dust 

The heater is not waterproof. This means that it may not be exposed to rain, spry or dripping 
water. The IP classification is IP00B 
The appliance is not designed for use in a very dusty environment. Dust may accumulate in the 
heater and may cause a defect of the heater. This is also the case for the room-thermostat. 

2.2.5 Protection against dust 

The appliance is not designed for use in a very dusty environment. Dust may accumulate in the 
heater and may cause a defect of the heater. This is also the case for the room-thermostat 

2.2.6 Temperature 

Do not install the heater in places where the temperature can rise above 35°C. At higher 
temperatures the internal components will degrade much faster. This is not covered by the 
guaranty. 

2.2.7 Corrosive environment 

The heater should not be installed in areas containing any corrosive or explosive vapours. It 
should be prevented that chlorine or other corrosive containing vapours are sucked into the air 
intake. These vapours will result in corrosion of the heat exchanger and a leakage of 
condensate and flue gas. Defects caused by this are not covered by guaranty. Please consult 
your supplier. This is also the case for the room-thermostat 

2.2.8 Installation distances 

Keep sufficient distance between the heater and any obstruction , in connection with safety and 
access for service and maintenance. Pay particular attention to any flammable  materials.  
Please take into account the possibility to open the door of the heater for the necessary service 
and maintenance work . Make sure the air flow to and from the heater is unhindered. Any 
obstacles should be a minimum of  5 metres away from the front of the heater. Read the 
chapter “Installation” carefully. 

2.2.9 Maintenance 

For the safe and proper operation of the heater periodical maintenance is necessary. When the 
heater is not serviced and cleaned in time, it could lead to damage of the heater or its 
surroundings.  

2.3  Guarantee 

The guarantee becomes void when the air heaters are not installed and serviced in accordance 
with this manual.

 

 

Summary of Contents for XR Series


























Reviews: