4
5
MX1200XTX/MX1200XTP/MX1200XTS OPERATION
1. Before starting, make sure that the blender is unplugged.
2. With the unit in Off position, place container on blender base. Be sure
container is fully seated and that drive coupling is properly engaged.
Plug blender cord into outlet.
3. Put ingredients into container and cover it. Do not fill above MAX line.
4. This blender has variable speed controls. Set blender to desired speed
between 1 and 10.
5. The left paddle switch defaults to the VARIABLE setting in order to use
the speed adjustment option. Press right paddle switch up to the ON
position.
6. When finished blending, set paddle
switch to Off position.
7. This blender is equipped with a
pulse option. Hold left paddle switch
in down position to engage pulse
function. Unit will run on max speed
(30,000 RPMs) until the paddle switch
is released.
8. Allow motor to come to a complete
stop before removing container
from blender base. Never place
the container on the motor base or
remove it from the motor base while
motor is running.
9. Always hold container with one hand when starting and while blending.
Never operate without jar lid.
10. Wash and dry container after each use. See cleaning and sanitizing
instructions, pages 5-7.
RESETTING THERMAL PROTECTION
• Your blender is equipped with an automatic reset function to protect
the motor from overheating.
• If your blender stops running under heavy use, turn the power switch
Off and unplug the power cord. Empty the blender container of all
its contents and allow between 5 to 30 minutes for the motor to
cool down.
• Plug the power cord back into the outlet and continue blending.
• If your blender does not function properly following this procedure,
discontinue use and contact a certified Waring Customer Service Center.
IMPORTANT
HOT BLENDING INSTRUCTIONS
To minimize the possibility of being scalded when blending hot materials,
the following precautions and procedure must be observed.
• Hot materials are those that are 100°F (38°C) or hotter.
• Limit the amount of materials processed to 1 pint.
• Completely remove the center portion of the two-piece container lid
before starting motor (this will allow venting of the rapidly heated and
expanding air inside the container when blender is running).
• Always start blending on lowest speed setting, and then progress to
desired speed.
• Never stand directly over blender when it is being started or while it
is running.
CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE
OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL
TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY,
RENDERING THEM INEFFECTIVE.
•
Wash, rinse, sanitize and dry container prior to initial use and whenever it
will not be used again within a period of 1 hour.
•
Wash and rinse container after each use.
•
Clean and sanitize motor base prior to initial use and after each use.
•
Washing solutions based on non-sudsing detergents and chlorine-based
sanitizing solutions having a minimum chlorine concentration of 100 PPM
are recommended.
The following washing, rinsing, and sanitizing solutions, or their equivalents,
may be used.
SOLUTION
PRODUCT
DILUTION IN WATER TEMPERATURE
Washing
Diversey Wyandotte
4 tablespoons
Hot 115˚F (46˚C)
Diversol BX/a or CX/A
/gallon
Rinsing
Plain Water
Warm 95˚F (35˚C)
Sanitizing
Clorox
®
1 tablespoon/gallon
Cold 50-70˚F
Institutional Bleach
(10-21˚C)
•
In repetitive batch-processing applications, frequent cleaning of the
container will prolong the life of the blade assembly. In no case should
actual running time between cleanings exceed one-half hour.
•
Do not use container to store processed foods or beverages.
