manualshive.com logo in svg

Waring FP40, Operation Manual, Page: 24 / 28

Share
Download
Waring FP40 Operation Manual Download Page 24

CLEANING

Clean the food processor and accessories prior to initial use and after each use. Do not use harsh abrasive-

type cleaners on any part of the food processor. Cleaning must follow NSF guidelines.

Wash the motor shaft with a small brush.

Wash, rinse, sanitize and dry the bowl, continuous feed chute, covers, small food pusher, large food pusher,

accessory discs, S-blades and ejector/slinger disc prior to initial use, and after use, unless they will be used

again immediately. These items are all dishwasher safe, and may be cleaned and rinsed in the dishwasher

instead of manually in the sink.

Wash and rinse all of the above items after each use.

Some of the discs and blades have aluminum components. Whether cleaning them manually or in a 

dishwasher, be sure to use a detergent that is safe for use with soft metals. Other types of cleaning 

detergents can cause corrosion of soft metals.

A stiff bristle brush will help to knock food particles out of the crevices of the discs and blades before 

washing. Handle very carefully as the blades are sharp.

Please note that all accessory discs and blades may be disassembled with a screwdriver for thorough 

cleaning. This includes the cutting blades on the center hub of the S-blade. Handle the sharp S-blade 

with care.

For manual cleaning, it is recommended that you use washing solutions based on non-sudsing detergents,

and chlorine-based sanitizing solutions that have a minimum chlorine concentration of 100 PPM. 

The following washing, rinsing, and sanitizing solutions, or their equivalents, may be used:

SOLUTION

PRODUCT

DILUTION IN WATER

TEMPERATURE

Washing:

Diversey

®

4 tablespoons per 

Hot 115°F (46°C)

Wyandotte

gallon

Diversol

®

BX/A or CX/A

Rinsing:

Plain Water

Warm 95°F (35°C)

Sanitizing:

Clorox

®

1 tablespoon per

Cold 50°F (10-21°C)

Institutional

gallon

24

Summary of Contents for FP40





























Reviews:

No comments