5
2018148_a•en•2017-04-01
We reserve the right to make technical changes
Example 3:
Cn existing unit with a WMS Hand-held transmit-
ter plus is expanded to include another WMS
Hand-held transmitter plus
Step 1:
Cdd a WMS Hand-held transmitter plus (2) to the exist-
ing network with a WMS Hand-held transmitter plus (1)
Button/
display
Cction/result
Wake up the WMS Hand-held transmitter
plus (1) with the STOP button
.
Wake up the WMS Hand-held transmitter
plus (2) with the STOP button
.
Press the learn button on the WMS
Hand-held transmitter plus (1) for approx.
5 seconds.
+
lights up green; the transmission LED
flashes. For several seconds, the WMS
Hand-held transmitter plus (1) scans the
operating range for devices.
The WMS Hand-held transmitter plus (1) does
not find any device during scanning:
The transmission LED
lights up.
IRCOGE
:
No receiver found.
If the WMS Hand-held transmitter plus (1)
finds a receiver, transmitter or sensor that has
not yet been learned in, scanning is stopped.
It is indicated as follows:
The transmission LED
lights up.
RED:
New receiver
When you press the control button
,
you can check WHICH target device was
just found.
The product then waves and the control
function LED
flashes
.
RED:
The target device (transmitter or sensor)
can be added to the network.
Press the STOP button
.
The found target device (transmitter or
sensor) is added to the network.
The target device waves in confirmation.
Briefly press the learn button
to leave
the learn mode.
Step 2:
Copy a channel from one WMS Hand-held transmitter
plus (1) to another WMS Hand-held transmitter plus (2)
Button/
display
Cction/result
+
Select the channel on the WMS Hand-held
transmitter plus (1) using the
+
button.
Briefly press the learn button on the WMS
Hand-held transmitter plus (1).
L LED
lights up green.
+
Select the channel on the WMS Hand-held
transmitter plus (2) using the
+
button.
IUTCE
O
If an unassigned channel is
selected, press the
+
button for
5 s. As soon as the LED flashes,
all channels can be selected by
pressing the
+
button again.
Button/
display
Cction/result
Briefly press the learn button on the TARGET
TRANSMITTER (WMS Hand-held transmitter
plus (2)).
L LED
lights up green.
The transmission LED
on the WMS
Hand-held transmitter plus (1) flashes.
GREEO
During the transmission of data from
the WMS Hand-held transmitter plus (1) to
the
WMS Hand-held transmitter plus (2); this
ends with
GREEO
Lights up continuously for 2 seconds,
transmission successful
RED
Lights up continuously for 2 seconds,
error during transmission
The L LED
on the WMS Hand-held
transmitter plus (1) and (2) goes out.
Example 4:
Uhe existing unit with a WMS Hand-held trans-
mitter plus is expanded to include a WMS Hand-
held transmitter
Step 1:
Cdd a WMS Hand-held transmitter to the existing net-
work with a WMS Hand-held transmitter plus
Button/
display
Cction/result
Wake up the WMS Hand-held transmitter
plus with the STOP button
.
Wake up the (large) WMS Hand-held trans-
mitter with any
product button.
Press the learn button on the WMS Hand-
held transmitter plus for approx. 5 sec-
onds.
+
lights up green; the transmission LED
flashes. For several seconds, the
(large) WMS Hand-held transmitter scans
the operating range for devices.
The WMS Hand-held transmitter plus does
not find any device during scanning:
The transmission LED
lights up.
IRCOGE:
No receiver found.
If the WMS Hand-held transmitter plus finds
a receiver, transmitter or sensor that has not
yet been learned in, scanning is stopped. It is
indicated as follows:
The transmission LED
lights up.
RED:
New device
When you press the control button
,
you can check WHICH target device was
just found.
The product then waves and the control
function LED
flashes
.
RED
:
The target device (transmit-
ter or sensor) can be added
to the network.