background image

3

 

 

Introduction

 

 

 

 

Thank you for purchasing the MR105D SafeAir® Room Oxygen Monitor. This product is 

manufactured and tested to the highest standards.

 

 

The unit also complies with the following standards: 

 

EMC Directive 2014/30/EU; 

 

Low Voltage Directive 2014/35/EU; and 

 

RoHS Directive 2011/65/EU          

 

 

Important note: 

The Oxygen Monitor unit is MR Unsafe and must not be taken into the MR 

room.  

 

 

 

To ensure that you obtain maximum benefit from your product, please take a few minutes to read 

the enclosed information regarding operation, service and maintenance.

 

  

If you have any problems in the meantime or would like any advice about this or any other MR 

products from the Wardray Premise range, please contact us at our 

Head Office

:

 

  

 

Wardray Premise Limited, Hampton Court Estate, Summer Road

 

Thames Ditton, Surrey, KT7 0SP, UK

 

  

Tel: +44 (0) 20 8398 9911

 

Fax: +44 (0) 20 8398 8032

 

  

E

-

mail:  

sales@wardray

-

premise.com

 

 
 

Kindly note:

 

If you modify a Wardray Premise product you will invalidate your warranty.

 

Unless you have our express written permission to modify a product, we transfer all liabilities for 

modified products to you.

 

 

 

 

EU Authorised Representative:

 

Advena Ltd

 

Tower Business Centre

 

2

nd

 Floor, Tower Street

 

Swatar

 

BKR 4013

 

Malta

 

Summary of Contents for SafeAir Room Oxygen Monitor
















Reviews: