background image

15

Wanner Engineering, Inc.

United States 

Instant Information:   www.stancorpump.com

(61) 33-5681   Fax (61) 33-6937 

 SCM-991-400A

Limited Warranty

Wanner Engineering, Inc. extends to the original purchaser 

of equipment manufactured by it and bearing its name, a 

limited one-year warranty from the date of purchase against 

defects  in  material  or  workmanship,  provided  that  the 

equipment is installed and operated in accordance with the 

recommendations and instructions of Wanner Engineering, 

Inc. Wanner Engineering, Inc. will repair or replace, at its 

option,  defective  parts  without  charge  if  such  parts  are 

returned with transportation charges prepaid to Wanner 

Engineering,  Inc.,  1204  Chestnut  Avenue,  Minneapolis, 

Minnesota  55403.
This warranty does not cover:
1.  The  electric  motors  (if  any),  which  are  covered  by 

the  separate  warranties  of  the  manufacturers  of  these 

components.
2. Normal wear and/or damage caused by or related to 

abrasion,  corrosion,  abuse,  negligence,  accident,  faulty 

installation or tampering in a manner which impairs normal 

operation.
3. Transportation costs.
This  limited  warranty  is  exclusive,  and  is  in  lieu  of  any 

other warranties (express or implied) including warranty 

of  merchantability  or  warranty  of  fitness  for  a  particular 

purpose  and  of  any  noncontractual  liabilities  including 

product  liabilities  based  on  negligence  or  strict  liability. 

Every  form  of  liability  for  direct,  special,  incidental  or 

consequential  damages  or  loss  is  expressly  excluded 

and denied.

Warranty

Summary of Contents for STAN-COR MK Series

















Reviews: