background image

4

MN-111 | Service book | Errors and Troubleshooting MN-111 ENG Rev08 | 2019/06/21 | © 2019 W&H Sterilization Srl

About this manual

MANUAL CONTENT

This manual contains the Instructions for use and for maintenance of the following sterilizer versions:

n

MN-111 100–125 V ac

n

MN-111 200–240 V ac

n

MN-111 Med 100–125 V ac

n

MN-111 Med 200–240 V ac

Versions differ for nominal voltage, maximum current, chamber material (AISI 304 or 316) and some functionality between W&H
and W&H Med versions.

DISCLAIMER

All pictures, graphics and illustrations provided in this manual are for the comprehension of the text. They are not meant to be an
accurate representation of product details. Thus, they should be taken as indicative only, and may differ from the actual product.

For any suggestions or remarks please send an email to [email protected].

COPYRIGHT NOTICE

Copyright © 2019, W&H Sterilization Srl

All rights reserved in all countries.

All drawings, images and texts contained in this manual are the property of the manufacturer. Even partial duplication of drawings,
images or text is prohibited.

The information contained in this document is subject to change without prior notice.

Summary of Contents for MN-111























Reviews: