W&H Lisa VA131-17 Instructions For Use Manual Download Page 116 | Manualshive

Page: 116 / 140

background image

116

LISA | Instructions for Use | VA131 2019 ENG Rev06 | 16/04/2020 | © 2020 W&H Sterilization Srl

Technical data

CONTENTS

This section deals with the following subjects:

Sterilization cycles

Sterilization cycle phases

Recommendations for validation

Accessories, spare parts, consumables

Authorized W&H service partners

Sterilization cycles

WARNINGS

For your safety and for the safety of your patients:

WARNING!
Never process objects different from those specified in the cycle program table and never exceed the maximum load weight limits
specified in it as this could impair the sterilization process. Such actions could result in non-sterile conditions at the end of the cycle,
could expose people to the hazard of cross-infections, are considered as an improper use of the sterilizer for which the manufacturer
cannot be hold responsible.
All indications of sterile load or successful completion of the cycle that are given on the display at the end of the cycle are not valid if
the type and quantity of the load are not complied with.
Processing bagged items with the S Fast 134 cycle will result in wet bags/pouches at the end of the cycle, exposing the items to
contamination due to improper storage. The display reminds the maximum permitted load before starting a cycle.

«
...
114
115
116
117
118
...
»

Summary of Contents for Lisa VA131-17













































































































































Reviews:

No comments

Related manuals for Lisa VA131-17

Brand: Rangevision Pages: 31

Brand: YSI Pages: 70

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Ultimate Healthcare Pages: 2

Brand: Ultimate Healthcare Pages: 40

LED Street Bar 16x3W RGB IP65

Brand: Varytec Pages: 9

Brand: VARILITE Pages: 8

EVENTPROFILE VL800

Brand: Vari Lite Pages: 34

Optica 30 Series

Brand: Varex Imaging Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands