WALTHER PILOT IV, Operating Instructions Manual

Page: 11 / 17

21 20
Listing of Replacement Parts PILOT IV GM
Item Part No. Description
No.
1 V 01 101 03 000 Retaining Nut f. Air Cap
2 optional Air Cap
V 01 101 02 . . 2* 2-Bore
V 01 101 02 . . 4* 4-Bore
V 01 101 02 . . 6* 6-Bore
3 optional Material Nozzle
V 01 101 10 . . 1* (also available in stainness steel)
4 V 10 441 03 000 Packing Gland Screw
5 V 09 101 74 000 Needle Seal Packing
6 V 00 130 01 040 Gravity-Feed Cup
7 V 00 130 03 040 Cover for Feed Cup
8 V 11 441 01 000 Gun Body
9 V 10 406 01 . . 3* Material Needle
10 V 10 206 02 000 Needle Retaining Nut
11 V 10 206 04 000 Needle Spring
V 10 206 05 060 Set Adjusting Screw compl.
consisting of:
12 V 10 206 06 000 Spring Retaining Bush
13 V 11 506 07 000 Lock Nut
14 V 10 206 05 000 Adjusting Screw
15 V 10 204 14 000 Valve Housing
16 V 09 101 14 000 Seal
17 V 10 204 03 000 Valve Spring
18 V 10 904 02 000 Valve Cone
19 V 10 444 01 000 Valve Shank
20 V 00 101 01 000 Double Nipple
21 V 00 101 74 750 Air Regulating Valve compl.
22 V 09 101 15 000 Packing (6 Disks)
23 V 10 201 06 000 Valve Bushing
24 V 00 103 06 000 Trigger
25 V 00 103 04 000 Nut for U-Bolt
26 V 00 103 07 000 U-Bolt
27 V 10 101 19 000 Spring for Trigger-Mount
28 V 10 101 18 000 Trigger Screw
Replacement Parts PILOT IV (deviating from PILOT IV GM)
29 V 11 401 01 000 Gun Body (Nickled Brass)
30 V 00 101 09 000 Air Tube
31 V 00 101 10 000 Gun Handle
32 V 00 101 08 000 Retaining Nut for Air Tube
33 V 00 101 05 000 Reducer
When ordering replacement parts please quote the respective size/s. lt is recommended to
keep in stock all bold-printed parts (wearing parts) to avoid work stoppages.
1 General
1.1 Identification of Model Versions
Models:
Hand-held Spray Guns PILOT IV / PILOT IV GM
Type: PILOT IV Gravity-Feed Cup V 11 401
PILOT IV GM Gravity-Feed Cup V 11 441
Manufacturer: WALTHER Spritz-und Lackiersysteme GmbH
Kärntner Str. 18-30
D-42327 Wuppertal
Tel.: 00 49 (0)202 / 787-0
Fax: 00 49 (0)202 / 787-2217
www.walther-pilot.de • Email: info@walther-pilot.de
1.2 Normal Use
The hand-held spray guns PILOT IV and PILOT IV GM are exclusively designed for
use with sprayable media. Spraying aggressive media should be avoided as the
wetted parts are not made of stainless specialty steel.
The guns are especially suited for processing / handling paints and lacquers, primers
and fillers.
Please note that sprayable materials may only be applied to work pieces and/or
similar items.
The temperature of the spraying materials shall never exceed 43° C. The term
normal use also implies that any and all safety warnings, operational handling
details, etc., as stated in these operating instructions, are carefully read, understood
and duly complied with.
This equipment complies with the explosion protection requirements of Directive
2014/34/EU (ATEX) for the explosion group, equipment category and temperature
class indicated on the type plate. When using the equipment, the requirements
specified in these Operating Instructions must be observed at all times.
The technical data indicated on the equipment rating plates and the specifications in
the chapter "Technical Data" must be complied with at all times and must not be
exceeded. An overloading of the equipment must be ruled out.
The equipment may be used in potentially explosive atmospheres only with the
authorisation of the relevant supervisory authority.
The relevant supervisory authority or the operator of the equipment are
responsible for determining the explosion hazard (zone classification).