background image

15

Chapter 5 Placement of Decals

All decals must be in place and legible or all warranties are void.

ITEM

DECAL

QTY

PART NO.

LOCATION

1

Safety Instructions

1

80100850

Locate in a conspicuous place near controls.

Operation Decal

1

80101696

Hazard Decal

1

80101370

Remote Circuit Breaker Decal

1

80100828

1000 lb Capacity Decal

4

80100250

Locate one in a conspicuous place near controls, and 
one on driver side column. Locate one on both sides of 
platform.

1650 lb Capacity Decal

80100268

2

Platform Caution Decal

4

75089296

Locate one in a conspicuous place near controls.
Locate one in a conspicuous place on driver side of 
vehicle.
Locate one on either side of platform

3

Access Door Decal

2

75089282

Locate one on chain anchor bracket.
Locate one on back of crossbeam box.

4

Cab Shut off Decal

1

75089267

Locate next to cab shut-off switch inside vehicle

5

Hazard Decal

2

80101370

Locate on access door

6

Warning Decal

1

80100829

Locate next to liftgate circuit breaker.                             
In applications where more than one circuit breaker is 
used, decal must be placed in both locations.

To maximize decal adhesion to surfaces:

               If your liftgate is equipped with dual

-

Surface must be dry and clean

               controls, an additional Safety Instruction

-

Firm pressure must be applied to decal

               decal (80100850) is to be placed in a

-

Minimum surface temperature 65 degrees F

               conspicuous place near the second set

(Heat gun may be used to heat surface)

               of controls.

Summary of Contents for FM Series





















Reviews: