walser TRANSPORTER PLUS, Mounting Instruction

Page: 4 / 12

4
EN: Instructions for use
Read the mounting and safety instructions carefully
1. Read and keep the instructions for use
This instruction manual belongs to this car seat cover. The installation and
safety instructions contain important information on commissioning and
handling.
Read the instructions for use, especially the safety information, carefully before using
the product. Failure to observe these assembly and safety instructions can lead to
serious injuries or damage.
Keep the instructions for use for future reference. If you pass the product on to third
parties, be sure to include these assembly and safety instructions.
2. Explanation of warning symbols and notes
The following symbols and signal words are used in these operating instructions.
Warning This signal symbol / word indicates a hazard with a medium
level of risk which, if not avoided, can result in death or seri-
ous injury.
Note This signal word warns of possible property damage.
Information This symbol gives you useful additional information on ins-
tallation and use.
3. Intended use
The seat covers are designed exclusively for covering standard vehicle seats. They are
intended exclusively for private use and not suitable for commercial use.
Use the seat covers only as described in these operating instructions. Any other use
is considered improper and can lead to property damage or even personal injury. The
seat covers are not a children‘s toy.
Only install the seat covers in vehicles for which they were manufactured (custom fit).
The manufacturer or dealer assumes no liability for damage caused by improper or
incorrect use.
4. Safety instructions
4.1 Safety instructions for driver and front passenger seat covers
Warning
Risk of death!
Correct initial assembly or attachment of the seat cover to the vehicle is
essential to guarantee the safety of the user. If the seat airbag is not in-
stalled correctly, it cannot be guaranteed that the seat airbag will eject
properly in the event of an impact.
→
Attach the seat covers as described in these operating instructions.
→
When attaching the seat covers, make sure that they are correctly assig-
ned (driver or front passenger seat cover). The side of the backrest covers
with the „airbag“ patches on the side must rest on the backrest side with
the airbag label on your seat.
→
Under no circumstances may the cover openings be manipulated (no
covering, sewing or repairs yourself)
→
Reposition the seat covers if they are displaced or damaged. If this is
no longer possible due to advanced wear, the cover must be removed or
replaced.
→
On no account attach the seat covers if they are visibly damaged or
deformed.
→
Never manipulate, repair or sew the special side airbag seams on the
seat covers.
→
Headrest entries, backrest adjustment levers / wheels for backrest un-
locking or armrests must not be covered with the seat cover. Proper cut-
outs must be made. Please note the following mounting steps (point 5).
4.2 General safety instructions
Warning
Suffocation hazard!
When children play with the seat covers, they can get caught in them or
pull them over their heads and suffocate.
→
Do not let children play with the seat covers.
Note
Risk of damage!
Improper handling of the seat covers can damage the seat covers.
→
Never place the seat covers on or near hot surfaces (e.g. stove tops).
→
Never expose the seat covers to high temperatures or the elements
(e.g. rain).
For removing and installing the headrests, please refer to the manufactu-
rer‘s information for your vehicle.
5. Mounting instructions
Covering the headrest
A
Roll up the cover like a sock and put it over the headrest. If the material is not
elastic, the cover may be a little more difficult to put on.
TIP: Take the headrest from the original seat (if possible). The attachment of the
headrest varies from vehicle to vehicle. Read the operating instructions for your
vehicle or ask at your car workshop.
Covering the armrest
B
If your vehicle is equipped with an armrest, remove the armrest from the original
seat before covering the seatback.
TIP: The mounting of the armrest varies from vehicle to vehicle. Read the manual
of your car or ask your garage.
C
Roll up the armrest cover like a stocking and cover the armrest of the original
seat. If your new seat cover is covered with foam, covering the original seat will be
somewhat more difficult.
Covering the front seats/individual seats
Covering the backrest
D
Roll up the backrest of your new seat cover like a sock and cover the backrest of
the original seat. If your new seat cover is covered with foam, covering the original
seat will be a little more difficult.
Pull a flap through between the seat and the backrest or fix it between the back -
rest and the seat part if the flap cannot be pulled through completely.
E
Make sure that all cut-outs are in the intended place. All the necessary openings,
such as for the headrests or the side lever, are already pre-punched and fit per -
fectly.
F
Slide the recesses for the headrest under the holder. Now the headrests can be
refitted.
Covering the seat part
G
Place the seat part of the cover on the seat surface of your car seat and smooth
everything down. Hook the rubber loops with hooks under the seat.
TIP: Due to the panels on the front seats, some side parts of the seat are of dif-
ferent lengths. So if the length of the side parts appear incorrect, please check
whether you might have swapped the covers for the seat part with the back part.
Covering the rear seat/double bench/3-seater bench
Covering the bench/seat surface
H
Lay the seat part of the cover on the seat of your bench and smooth everything
out. Then attach the cover to the underside and back of the bench using rubber
loops and hooks. Do not stretch the rubber loops in the rear part of the seat to-
wards the center of the seat, but outwards or backwards. The seat cover is made
to disappear under the trimmed part of the seat.
Covering the backrest
I
Roll up the backrest section like a sock and cover the backrest of the original seat.
If your new seat cover is covered with foam, covering the original seat will be a
little more difficult.
J
Make sure that all cut-outs are in the intended place. All the necessary openings,
such as for the headrests, are already pre-punched and fit perfectly. Slide the
headrest recesses under the bracket.
K
Now the headrests can be refitted.
Your cover does not seem to fit correctly?
The edges of the original seat must match the side seams of the cover. If it doesn‘t,
adjust it. The final adjustment to the shape of your backrest takes place after you have
used the cover for a few days.
6. Cleaning
Pay attention to the textile care symbols on the sewn label.
7. Disposal
The seat covers can be disposed of with the residual waste.
Dispose of the packaging according to type. Dispose of cardboard and cardboard as
waste paper and foils in the recyclable material collection.
8. Service and Support
If you have any questions about the product, please contact office@walsergroup.com