background image

3

1.  General information

1.1.  Note symbols

Danger

Immediate hazard
Failure to observe the warning will result in immedi-

ate death or serious injury.

Caution

Low-risk hazard
Failure to observe the warning may result in 

moderate injury.

Warning

Potential hazard
Failure to observe the warning may result in death or 

serious injury.

Important

Danger with risk of damage to property
Failure to observe the warning may result in 

damage to property.

Note

Useful information and instructions

2.  Important safety instructions

Planners, system builders and operators are responsible for proper installation and operation in accordance with the inten-

ded use.

• 

Read the operating instructions completely and carefully.

• 

Operating instructions and applicable documents, such as electrical connection diagrams or operating instructions for 

the motor, must be kept with the fan. They must be available at the place of use at all times.

• 

Local and national laws and regulations must be observed and complied with.

• 

Take into account the system-relevant conditions and requirements of the system manufacturer or system builder.

• 

Safety devices must not be dismantled, bypassed or rendered inoperative.

• 

The fan may only be used in perfect condition.

• 

The generally prescribed electrical and mechanical protective devices must be provided.

• 

Secure the installation site and the premises against access by unauthorised persons during installation, electrical 

connection, commissioning, troubleshooting and maintenance.

• 

Safety devices must not be dismantled, bypassed or rendered inoperative.

• 

Ensure that all warning labels on the fan are complete and legible.

• 

This appliance is not intended for use by persons (including children) with reduced physical or mental capabilities, 

or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the 

appliance by a person responsible for their safety.

• 

Children must not play with the appliance.

2.1.  Personnel

The fan may only be operated by qualified, instructed and trained personnel. These persons must know the relevant safety 

regulations in order to recognise and avoid possible dangers. The individual actions and qualifications can be found in Table 

1 Qualification.

Summary of Contents for GB

























Reviews: