background image

10/22/2019 
          2/2E

LINKABLE SET-UP INSTRUCTIONS

FCC WARNING

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to 
operate the equipment.

Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate 
radio frequency enerqy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio 
communications. 
However, there is no quarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.

WARNING:

 

 

Do not dispose of lithium batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or destroy 

batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, 

standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries .

(E) Link button

(D) Power switch

LINKABLE SOLAR LED FENCE LIGHT

ITEM: Q01DA0429-08

Make sure the LED lights are directed away from your eyes then move the power 
switch to the “ON” position. 
Among all the lights, select one as the parent light (PL), and the others as the 
children lights (CL).

2)

1)

3) (CL): Move the link button (Part E) to the “LINK ON” position (direction of arrow) on all 

children lights (CL) you want to connect to the parent light (PL). Keep in the “LINK ON” 
position for one second, then switch the link button (Part E) back to its initial 
position quickly. The (CL) will start flashing every second, now they are in link mode.
All (CL) after complete step 3) operation, time to place the (PL) in link mode.

4) (PL): Move the link button (Part E) to the “LINK ON” position (direction of arrow). Keep 

in the “LINK ON” position for 5 seconds, then the parent light (PL) will flash very slowly 
(flashing every 4 seconds). The (PL) is now in link mode and sending signals to pair 
with the selected (CL). 

5) Once the (CL) in link mode receives and saves the paired ID code signal transmitted 

by the (PL), completes and exits the pairing mode. The blinking light(s) will stop 
flashing and resumes normal use. Make sure that all (CL) pairs are completed.

6) (PL): Move the link button (Part E) for parent light (PL) back to its initial position. 

The blinking light(s) will stop flashing and resumes normal use. Now the (PL) 
is linked with the (CL), the linking process is complete. When any of the lights (PL) 
or (CL) are triggered by motion, all lights will activate.

Note: Light will stay on 30 seconds when triggered by motion. Detection range is 19.69-26.2 ft (6-8m), detection angle is 120°. Light use radio 
frequency technology to link, and should not be greater than 49.2 ft (15m) between the neighboring/adjacent lights. 
If you buy a new linkable solar light and want to add it into the “family" , you can re-start this LINKABLE SET-UP INSTRUCTION again for all 
the lights you want to link. 
If you want one of the (CL) to unpair, turn link button (Part E) to the "LINK ON" position (direction of arrow), stay for more than 5 seconds, the (CL) 
will flash very slowly (flashing every 4 seconds). then turn back to the original position. Then this (CL) is unpaired.
Precautions:
1: The luminaries that are paired with the code are not completed in the normal steps. After the power is turned off, the power is turned on 
again to resume normal operation.
2: The code switch is mis-operated when the code is not being used. It needs to be powered off again and then powered back on to resume 
normal operation.

TM

Distributed by/Distribuido por

Wal-Mart Stores, Inc.,

Bentonville, AR 72716

MADE IN COUNTRY/HECHO EN COUNTRY

©2019 Wal-Mart Stores, Inc.

Hyper Tough is a registered trademark of

Wal-Mart Stores, Inc. All Rights Reserved.

For assistance with assembly or instruction, parts and customer service, call: U.S.A. & Canada only: 1-844-551-0680

8am – 5pm Monday – Friday, Central Standard Time Or email: [email protected]

Summary of Contents for HYPER TOUGH Q01DA0429-08

Page 1: ...light over the screw heads x x 4 7in C Light Fixture X 1 B Wall Anchor X 2 A Screw X 2 FOR FIRST TIME USE SOLAR LIGHT NEEDS TO CHARGE IN FULL SUNLIGHT FOR 8 12 HOURS WITH THE SWITCH IN THE ON POSITION TO FULLY CHARGE THE RECHARGEABLE BATTERY IF INSTALLING MORE THAN 1 LIGHT YOU MUST LINK YOUR LIGHTS FIRST BEFORE INSTALLATION BEGINS YOU MAY LINK UP TO 20 LIGHTS AFTER THE LIGHTS ARE LINKED YOU MAY BE...

Page 2: ...tial position quickly The CL will start flashing every second now they are in link mode All CL after complete step 3 operation time to place the PL in link mode 4 PL Move the link button Part E to the LINK ON position direction of arrow Keep in the LINK ON position for 5 seconds then the parent light PL will flash very slowly flashing every 4 seconds The PL is now in link mode and sending signals ...

Page 3: ...os Parte A al colocarlos orificios de la parte posterior de la lámpara en las cabezas de los tornillos PARA EL PRIMER USO LA LUZ SOLAR NECESITA CARGARSE BAJO LUZ SOLAR DIRECTA POR UN PERIODO DE ENTRE 8 Y 12 HORAS CON EL INTERRUPTOR EN LA POSICIÓN ON PRENDIDO PARA CARGAR TOTALMENTE LA BATERÍA RECARGABLE SI INSTALA MÁS DE 1 LUZ DEBE ACOPLAR SUS LUCES ANTES DE EMPEZAR LA INSTALACIÓN PUEDE VINCULAR HA...

Page 4: ...stán en modo de vinculación Todo CL después de completar el paso 3 operación es hora de colocar la PL en modo de vinculación 4 PL Lleve el botón de vinculación Parte E a la posición de LINK ON en la dirección que indica la flecha Mantenga en la posición de LINK ON durante 5 segundos la luz principal PL parpadeará muy lentamente cada 4 segundos La PL ahora está en modo de vinculación enviando señal...

Reviews: