Wallenstein LXG210 Series Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 36

background image

3.2 Safety Sign Explanations

1. Caution!

Hydraulic fluid under pressure. In the
event of a leak, shut machine down. Do
not check for leaks with bare hands. Wear
proper hand and eye protection when
searching for a high-pressure hydraulic
leak.

2. Warning!

Risk of falling debris from grapple. Do
not lift any load that cannot be safely
secured by the grapple. Never allow
anyone to walk under overhead load. Keep
bystanders at a safe distance.

3. Caution!

Be aware of pinch hazards from moving
parts such as boom, grapple, and logs.

4. Warning!

Be aware of crush hazards from moving
parts. Keep hands clear of the machine
during operation.

5. Caution!

Risk of machine moving unexpectedly
causing injury when servicing or
repairing. Shut down machine before
performing maintenance procedures.
Remove the ignition key.

6. Caution!

Refer to the operator's manual. Read ALL
operating instructions in the manual and
learn the meaning of ALL safety signs on
the machine.

The best safety feature is an informed
operator.

Safety Signs

LXG210 Series

Log Grapples

Safety

14

«
...
12
13
14
15
16
...
»

Summary of Contents for LXG210 Series





































Reviews:

No comments

Related manuals for LXG210 Series

Brand: Harbor Freight Tools Pages: 4

Brand: ICON Pages: 8

Brand: Olympus Pages: 2

Brand: Mahindra Pages: 25

Brand: Obelink Pages: 2

Brand: pleasant hearth Pages: 6

Brand: R&G Pages: 12

Brand: Datalogic Pages: 5

Brand: BabyOno Pages: 24

Brand: Ryobi Pages: 8

CV MY FIRST TRAMPOLINE AND ENCLOSURE

Brand: Chad Valley Pages: 15

Brand: poly-planar Pages: 2

Brand: Taylor-Dunn Pages: 182

Brand: Kabuto Pages: 28

Brand: Brinly Pages: 60

Brand: Perma Pure Pages: 25

Brand: SAN HIMA Pages: 7

THERMASGARD HFTM

Brand: S+S Regeltechnik Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands