background image

K00035

K00036

K00037

ø 75 mm

ø 111 mm

(4 

3

/

8

”)

23 mm

(

29

/

32

”)

ø 90 mm

(3 

17

/

32

”)

1

3

5

4

2

7

6

Installation

en

1.

Blower grill

2.

Adjustment valve

3.

Fastening screw

4.

Air duct

5.

Insulation

6.

Hose clamp

7.

Body

At least one of the two air outlets of the heater must be open at all 
times.

3416 silencer (accessory) 

For the war air tubing is available an silencer 3416 as an accessory, which effec-

tively reduces air flow noise. The silencer can be installed in the inlet-, or to the 

blower side.

Ventilation

An equivalent amount of air which is blown out through grills must  leave the cabin, 

either outdoors or as return air to inlet tubing.

Installation of the air registers

When installing the warm air register 

3411

 or 

2411

, remove the grill part (1) of the 

body (7) by pulling. The grill part can be turned 360° to be able to adjust the air flow 

direction.

3411

For installation, cut the bulkhead with ø 76 mm (3”) hole for the grill frame. Use 
screws to attach the grill frame (7) to bulkhead with three screws. In order to install 
warm air tubing drill a hole ø 83 mm (3 

1

/

4

”) to bulkhead.

2411

Cut a ø 67 mm (2 

5

/

8

”) hole in the bulkhead or wall.  Screw the body of the register 

(7) to the bulkhead with 3 screws.  Connect the warm air duct to the register and
reinstall the grill cover.

D10151A

- 81 -

22 GB / 30 GB 

490529

Summary of Contents for 30 GB







































Reviews: