background image

12 

After Each Use 

1. 

Clean the interior of the pan regularly after each use.  Do not use wire brushes on the pan.  Clean 

using a mild detergent and a hot water solution using soft cloth or a soft bristled brush.  Dry the 
appliance thoroughly using a dry clean cloth. 

 

Daily Cleaning 

1. 

The water should be drained and re-filled regularly.  Open the drain valve slowly to minimise 

splashing.  Waste water will drain into the tundish  fitted below the appliance drain outlet. 

2. 

When the tank is empty, open the drain valve fully and check for any particles or residue lodged in 
the valve.  Clean out with a stiff nylon brush.  Do not use a wire brush or metal rods as these 

damage the seating in the valve and will eventually lead to valve leakage. 

3. 

If the obstruction in the valve cannot be removed with a brush, use a wooden probe to dislodge any 
obstruction. 

4. 

Clean the control panel using a damp cloth lightly moistened with a solution of mild detergent and 

hot water.  Dry the control panel thoroughly using a dry clean cloth. 

5. 

Clean the interior and exterior of the pasta cooker regularly at the end of each day.  Do not use wire 

brushes on the pan.  Clean using a mild detergent and a hot water solution using soft cloth or a soft 

bristled brush.  Dry the appliance thoroughly using a dry clean cloth. 

6. 

Once the daily cleaning operation is completed, ensure that the drain valve has been closed. 

Cleaning and Maintenance

 

WARNING: 

 

H

OT

 

WATER

 

WILL

 

SCALD

 - 

DO

  

NOT

  

RUSH

  

THIS

  

JOB

WARNING: 

 

D

O

 

NOT

 

ATTEMPT

 

TO

 

MOVE

 

THE

 P

ASTA

 C

OOKER

 

WHILST

 

THE

 

COOKER

 

IS

 

FULL

 

OF

 

WATER

 

B

EFORE

 

ATTEMPTING

 

TO

 

MOVE

 

THE

 P

ASTA

 C

OOKER

ENSURE

 

THAT

 

ALL

 

THE

 

WATER

 

HAS

 

BEEN

 

DRAINED

 

FROM

 

THE

 

TANK

.  R

EFER

 

TO

 

THE

 

INFORMATION

 

ON

 

THE

 

PREVIOUS

 

PAGE

ON

 

HOW

 

TO

 

DRAIN

 

THE

 

WATER

 

FROM

 

THE

 

P

ASTA

 C

OOKER

Fig 3 

Locking Slide 

unlocked position 

Locking Slide 

locked position 

Fig 4 

Summary of Contents for PC8140E




















Reviews: