THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD HEAD LIGHT COVER FOR MERCEDES-BENZ W463 G-CLASS.
HEAD LIGHT COVER
Mercedes Benz
G-class
(W463)
【
BEFORE PAINTING
】
１）Remove OEM head light cover according
to the Mercedes-Benz service manual.
２）Temporarily install the attached LED lamps according
to the guide-wall on WALD Head Light Cover.
※
Adjust the details of WALD Head Light Cover to fit the
attached LED lamps by rasps or sandpapers.
３）Temporarily install WALD Head Light Cover to the body.
※
Adjust the details of WALD Head Light Cover to fit
the body by rasps or sandpapers.
４）Prepare to connect the LED lamps.
※
Insulate any spare harness.
５）Paint WALD Head Light Cover according to the picture.
【AFTER PAINTING】
６）Completely degrease the installation positions
for WALD Exhaust Trim.
７）Use caulking glue to fix WALD Exhaust Trim
on WALD Rear Bumper.
８）Leave them till completely fixed.
９）Install WALD Rear Bumper to the body.
2013/04
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
ATTENTION
PARTS
QUANTITIES
REAR BUMPER
1 SET
HEAD LIGHT COVER
LED LAMP
1 SET
Use caulking glue
to fill the gap
between the product
and the body.
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
※MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK. DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY.
ATTENTION
OEM TAPPING SCREWS
ATTACHED LED LAMP
OEM HEAD LIGHT WASHER
CAR SIDE
※Insulate OEM fog lamp harness.
LED LAMP
[ AS DAYLIGHT ]
IGNITION
GROUNDING WIRE
POSITION LAMP
RELAY
BOX
RED
BLACK
BLUE
＝ WIRING DIAGRAM ＝
■ HOW TO INSTALL THE
ATTACHED LED LAMPS (STEP 2, 7)
ATTACHED LED LAMP
(Inside of WALD Head Light Cover)
Fix the attached LED lamps according to the picture.
(Face of lens)
※ Use heat resistant caulking glue
to fix the attached LED lamps.
LED LAMP GUIDE-WALL
MATTE BLACK
※WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 5)
Make clear coating for the carbon parts
of WALD Front Bumper.
MBMANUALS.COM
