background image

Thank  you  for  purchasing  the  Wahl  DHS235XEL  non-
contact infrared thermometer. To  measure  a temperature, 
simply  point  the  unit  at  the  object,  pull  the  trigger  and 
read the display. Releasing the trigger will put the unit into 
hold  mode,  which  will  display  the  captured  reading  for 
approximately 6 seconds before powering off. Make sure 
the target area is larger than the unit’s spot size. For large 
target objects assure you are within target distance. 

 
 

 

The  DHS235XEL  features  a  wide  temperature  range, 
and high D:S (Distance to Spot) ratio, allowing the user 
to  measure  high  temperature  objects  from  a  safe 
distance. 

 

High DS ratio. 
Adjustable emissivity from 0.1 to 1.00 in 0.01 steps. 
Ultra low power consumption in shutdown mode. 
Extended long time measuring reliability. 
Backlit Liquid Crystal Display (LCD). 
°C or °F selectable. 
Electronic trigger lock. 

 
 

 

Electrical troubleshooting. 
Automotive repair and maintenance.  
Science experiment. 
Manufacturing processes of semiconductor technology. 
Test terminals on circuits. 
Food safety and processing. 
Perform HVAC energy audits. 

 
 
 

 

 

Read  the  following  safety  information  carefully  before 
attempting  to  operate  or  service  the  instrument.  Only 
qualified  personnel  should  perform  repairs  or  service  not 
covered  in  this manual.

 

 

 
 
 
 

    2-1 Warning 

 

DO NOT submerge the instrument in water 

This  product  is  not  designed  for  use  in  medical 
evaluations. 
This product is intended for use in industrial, scientific 
and educational purposes only. 

 

 

 

Dangerous, refer to this manual before using 
the meter. 

   CE Certification. 

This instrument conforms to the following standards: 

EN61326: Electrical equipment for measurement, 

control and laboratory use.

 

IEC61000-4-2: Electrostatic discharge immunity test. 
IEC61000-4-3: Radiated, radio-frequency,

 

electromagnetic field immunity test. 

IEC61000-4-8: Power frequency magnetic field

 

immunity test.

 

Tests were  conducted using  a  frequency  range  of  80-
1000MHz with the instrument in three orientations. The 
average  error  for  the  three  orientations  is  ±0.5°C 
(±1.0°F)  at  3V/m  throughout  the  spectrum.  However, 
between 781-1000MHz at 3V/m, the instrument may not 
meet its stated accuracy. 

Do not point laser directly at eye. Use 

caution around reflective surfaces. Keep out of 
reach of children. 

Summary of Contents for DHS235XEL









Reviews: