WAGO I/O SYSTEM 750 Quickstart Reference Download Page 45 | Manualshive

Page: 45 / 54

background image

WAGO-I/O-SYSTEM 750

Application example: Starterkit880_App1_FUP.pro

45

750-880 ETHERNET Programmable Fieldbus

Quickstart Reference

Version 1.0.0

6.

Select the driver "Serial (RS232) 3S Serial RS232 driver" and confirm your
input by clicking

[OK]

.

Figure 49: New communication channel via USB

7.

Double-click on the address field

COM1

in the column "Value" in the

"Communication parameters" dialog box. The field is highlighted in gray.

8.

Press the

[↓]

or

[↑]

arrow to increase or decrease the COM port number by

one. Adjust the COM port, which was previously identified in the Device
Manager (in this example "COM3"), accordingly in the Communication
Parameters.
You can leave all other parameters (Baudrate, Parity, Stop bits, Motorola
byteorder, Flow Control) and the gateway settings as they are. Confirm your
input by clicking

[OK]

.

Figure 50: USB communication parameters

«
...
43
44
45
46
47
...
»

Summary of Contents for I/O SYSTEM 750























































Reviews:

No comments

Related manuals for I/O SYSTEM 750

Brand: Gardi Systems Pages: 6

Brand: ICP DAS USA Pages: 6

Brand: M-system Pages: 3

Brand: M-system Pages: 13

Brand: RAM Pages: 32

Bell & Gossett ecocirc XL Series

Brand: Xylem Pages: 62

Institutional I-40

Brand: Hunter Pages: 2

Brand: AES Pages: 17

Brand: Aiphone Pages: 2

Brand: Genie Pages: 57

Brand: Serene Pages: 48

Brand: BERNSTEIN Pages: 52

Genie GS-2669 DC

Brand: Terex Pages: 147

Brand: Digitrax Pages: 8

Brand: HIKVISION Pages: 23

USB-1408FS-Plus-OEM

Brand: Measurement Computing Pages: 26

Brand: Aiwa Pages: 76

Brand: Idemia Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands