WAGNER PM500 Operating Manual Download Page 44

44

 

OPERATING MANUAL

VERSION 01/2013

ORDER NUMBER DOC 2335747

10 

SPARE PARTS

10.1 

HOW CAN SPARE PARTS BE ORDERED?

Incorrect maintenance/repair!

Risk of injury and equipment damage.

  Have repairs and part replacements be carried out only by 

specially trained staff  or a WAGNER service center.

 Before all work on the device and in the event of work 

interruptions:

 

- Switch off  the energy/compressed air supply.

 

- Relieve the pressure from the spray gun and device.

 

- Secure the spray gun against actuation.

  Always follow the operating and service instructions at all times 

when carrying out work.

WARNING

Always supply the following information to ensure delivery of the right spare part:

Order number, designation and quantity

The quantity need not be the same as the number given in the quantity column "

" on 

the list. This number merely indicates how many of the respective parts are used in each 
module.

The following information is also required to ensure smooth processing of your order:

Billing address
Delivery address
Name of the person to be contacted in the event of any queries
Type of delivery (normal mail, express delivery, air freight, courier)

Identifi cation in spare parts lists

Explanation of column " " (labeling) in the following spare parts lists:

Wearing part

Note

: No liability is assumed for wearing parts.

Not part of standard equipment, available, however, as additional extra.

Summary of Contents for PM500





















































Reviews: