manualshive.com logo in svg

WAGNER GA 5000EACIC, Operating Manual

Share
Download
WAGNER GA 5000EACIC Operating Manual Download Page 56

56

GA 5000EAC

OPERATING MANUAL

VERSION 09/2016

ORDER NUMBER DOC2360922

1.

Switch control unit to standby operation.

2.

Unscrew union nut completely (12) and remove air cap (10).

3.

Push ACF 5000 nozzle (11) out of air cap (10) by hand, reverse it and put it into the air 
cap (10) with the nozzle tip towards the rear.
Pay attention to the position of the guide surfaces (X).

4.

Insert air cap (10) with integrated ACF5000 nozzle (11) into the union nut (9).
Make sure that the air cap horns (Y) lie in the recess of the nozzle guard.

5.

Screw preassembled union nut (12) to gun (1) and tighten by hand.

6.

Switch on gun without high voltage and fl ush gun.

7.

When the blockage has been fl ushed out, switch control unit back to standby operation.

8.

Unscrew union nut (12) completely.

9.

Remove air cap (10) and push ACF5000 nozzle (11) out of the air cap by hand.
Clean ACF5000 nozzle and insert it in the spraying position into the valve housing.

10. Put the air cap (10) on the nozzle (11) and pay attention to the position of the guide 

surfaces (X).

11. Screw union nut with attached nozzle guard (9) to the gun body and make sure that 

the air cap horns lie in the designated recess (Y).

12. Before tightening with the air cap horns (Y), set the desired jet level and then tighten 

the union nut to stop by hand.

13. Switch control unit to the required operating mode.

7.3.10 

ELIMINATE NOZZLE CLOGGING

Summary of Contents for GA 5000EACIC













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands