manualshive.com logo in svg

WAGNER GA 5000EACIC, Operating Manual

Share
Download
WAGNER GA 5000EACIC Operating Manual Download Page 30

30

GA 5000EAC

Atomizing air

Zerstäuberluft

Fan air

Formluft

B_05769

B

GA 5000EACEC

GA 5000EACIC

A

OPERATING MANUAL

VERSION 09/2016

ORDER NUMBER DOC2360922

5.6 

THE WAGNER ELECTROSTATIC AIRCOAT SPRAYING SYSTEM

The nozzle range (chapter 13) provided by WAGNER allows optimum coating results for 
any application.

General criteria for selection of nozzles

Flat jet   for large-surface parts
Round jet   for smaller delicate parts

Options for infl uencing the jet spray / spray pattern:

Description

Modifi cation

Product pressure

+ or -

Atomizing air pressure

+ or -

Shaping air regulation

from open to closed

Nozzle sizes

Flow rate

Electrostatics

+ or - or off 

The spray jet width by GA 5000EACIC spray gun is adjusted via the shaping air regulation 
(A) on the gun and on the GA 5000EACEC spray gun via the air control knob (B) on the
EPG 5000 control unit in the case of fl at jet spraying.

Summary of Contents for GA 5000EACIC













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands