background image

EN

7

ASSEMBLY (iSPRAY NOZZLE)

iSPRAY ASSEMBLY

Attention

Make sure the power cord is unplugged.

1. 

Insert the suction tube into the intake opening. 

2. 

Align the pickup tube: 

  A  If spraying downward, the angled end of the pickup tube 

should be pointing toward the front of the nozzle.

  B  If spraying upward, the angled end of the pickup tube 

should be pointing toward the rear of the nozzle.

i

Make sure the pickup tube is inserted as far as it 

will go to ensure a tight fit.

3. 

Carefully screw the cup back onto the nozzle assembly.  

Tighten firmly.  

4. 

Align the nozzle and the handle approximately as shown.  

5. 

Insert and twist the nozzle into the handle toward the 

“lock” symbol on the handle.

    The tab below the trigger will lock the two pieces into 

place.

6. 

Insert the air hose tightly into the connection on the spray 

gun handle.  The connection can be positioned as desired.   

    Insert the air hose tightly into the connection into the 

turbine.  The connections can be positioned as desired. 

NEVER point the spray gun at any part of the 

body.

1

2

A

B

3

4

5

6

Summary of Contents for FLEXIO 4300

























Reviews: