background image

English

10

 

© Wagner Spray Tech - All Rights Reserved

Proper Spraying Technique

STOP

The room you are spraying must be 

properly masked in order to prevent 

overspray from covering woodwork, 

floors or furnishings.  Make sure you 

have properly masked the room per the 

instructions on the enclosed “Taping 

Guide”.

If spraying with an air-assisted spray system is new 

or unfamiliar to you, it is advisable to practice on a 

piece of scrap wood or cardboard before beginning 

on your intended workpiece and/or test with water.   

Surface Preparation

All objects to be sprayed should be thoroughly 

cleaned before spraying material on them.  Areas 

not to be sprayed may, in certain cases, need to be 

masked or covered.

Spray Area Preparation

The spray area must be clean and free of dust in 

order to avoid blowing dust onto your freshly 

sprayed surface.

How to Spray Properly

STOP

It is important to keep your arm moving 

whenever the gun is being triggered.  If 

you pause or linger in one spot too long, 

too much material will be sprayed to the 

surface. 

  •  Position the spray gun perpendicular to and 

six (6) or more inches from the spray surface, 

depending upon the spray pattern size desired.  

With reduced material flow and air power, you 

can get closer to the spraying surface.  

  •  Spray parallel to the surface with smooth passes 

at a consistent speed as illustrated below.  

Doing this will help avoid irregularities in the 

finish (i. e. runs and sags).

6 - 8 inches

Correct

Even coat throughout

Keep stroke smooth and at an even speed

  •  Always apply a thin coat of material on the first 

pass and allow to dry before applying a second, 

slightly heavier coat.  

  •  When spraying larger surfaces, overlap each 

spray pass by at least 50%  This will ensure full 

coverage.

  •  When spraying, always trigger the spray gun 

after spray pass has begun and release trigger 

before stopping the pass.  Always keep the 

gun pointed squarely at the spray surface and 

overlap passes slightly to obtain the most 

consistent and professional finish possible.

Incorrect

Do not flex wrist while spraying.

Light coat

Heavy coat

Light coat

note:  When you quit spraying for any length of 

time, turn the turbine OFF and place the spray 

gun into the spray gun holder on the turbine.
When you restart, wipe the nozzle with a damp 

cloth to remove any dried paint.  

Summary of Contents for 0529017





















Reviews: