background image

WAFER GSM-KEY REMOTE CONTROL UNIT 

http://www.waferstar.com 

PC Software interface: 

COM Port parameters config interface and connect to the device 

Before program the device through the PC,firstly you need to config the COM port paramters and 
then connect the device to PC software. 
Password is the PWD password, if no change,the initial password is “ 123456 ” 

 

 
 
 
Phone Numbers Setting interface: 

Normally you firstly would be better to get all numbers from the device unit, then would make 
sure to know which numbers are already inside the device. 
Before download the phone numbers,you need firstly select the right index number and then input 
the user details, after input ,then press the “ 

SET 

” button to set the input index to Red color, then 

press the button” 

Download All Phones

”, after download, it would turn to Green color. 

If you want to delete one index information,then you need to select the right index line and press 
the “ 

Delete

 ” button , and the press the button” 

Download All Phones

”. 

You can set or delete one or several index line information in one time. 
( Download All phones, that only means that is download all the 

SETTED numbers

 into the 

device ) 

Summary of Contents for AC200















Reviews: