background image

 Part number 20055, Rev 0 

 

RECEIVING 

Your unit was built, packaged, and inspected with extreme care. We shipped it to you using 
carriers we trust with a proven track record of careful handling, good customer service, and on 
time delivery.  Unfortunately, regardless of all of these efforts sometimes accidents happen and 
occasionally those accidents result in shipping damage. When the carrier picked up the 
merchandise from us, they assumed responsibility for its condition en route to you. Thus, any 
claims for shipping damage must be filed with the carrier. Like anybody else, carriers don’t like 
to pay out on insurance claims, so their claims procedures and requirements are very 
restrictive. You should consult the carrier’s website for their specific claims procedures. You 
should also know that time is of the essence.  

There are two general types of shipping damage. The first is

  visible damage

. This type of 

damage includes visible loss, damage, shortage or any external evidence of loss or damage that 
is visible at time of delivery

. This type of damage must be noted in detail on your delivery 

receipt. Make sure the driver signs and dates the delivery receipt, acknowledging the 
damage.

 This has to happen at the time of delivery or it won’t happen at all. Keep a copy for 

your records and send another to the carrier’s damage claims department along with a formal 
request for an inspection report. Follow up with a phone call. Their contact information can be 
found on the carrier’s web site.  

 The second type of shipping damage is 

concealed damage

. This type of damage will probably 

not be apparent at time of delivery and may not be discovered until unpacking and inspecting 
the unit. Remember, time is of the essence here. You should unpack and inspect the unit as 
soon as possible. Each day that passes reduces the likelihood that the carrier will pay the claim. 

As soon as the concealed damage is discovered, stop unpacking and retain all packing 
materials. Contact the carrier by phone to report the claim.

  Note the date and time and 

person you spoke with. Get a claim number. Follow up with a written letter referencing the 
claim number and including a formal  request for an inspection. Again, consult the carrier’s 
website for specific claim instructions and follow them precisely.  

AS STATED ABOVE, THE CARRIER IS YOUR SOLE SOURCE FOR SATISFACTION OF A DAMAGE 
CLAIM.  UNDER NO CIRCUMSTANCES SHOULD THE MERCHANDISE BE RETURNED TO  THE 
MANUFACTURER. NO RETURNS WILL BE ACCEPTED WITHOUT PRIOR AUTHORIZATION. 

Summary of Contents for SCPAF-3020





















Reviews: