background image

— 9 —

TURNING THE FRYER ON

To turn the fryer on, set the thermostat knob to the desired
temperature.  After the set temperature has been reached, the
gas control shuts off gas flow to the burners.  The pilot remains
lit. The burners will cycle on and off, maintaining the set
temperature.

TURNING THE FRYER OFF

1. Turn the thermostat OFF.

2. Turn the gas control valve knob to PILOT.  In this position

the pilot will remain lit.

3. To shut off all gas to the system, including the pilot, turn the

gas control valve knob to OFF.

EXTENDED SHUTDOWN

1. Turn the manual gas shutoff valve OFF.

2. Turn the thermostat knob OFF.

3. Turn the gas control valve knob to OFF.

FRYING FOODS

Heat shortening to set temperature.

Pieces of product to be fried should be about the same size to ensure the same doneness.

Drain or wipe dry raw or wet foods to minimize spatter when lowering into the hot oil.

Do not overfill baskets.

Carefully lower baskets into oil.

When frying doughnuts and fritters, turn product only once during frying.

When cooking French fries or onion rings, shake basket several times in a way that does not
spatter the shortening.

Batter-covered foods should be dropped carefully, one by one, into shortening or basket.  If you
use the basket, first dip basket into the shortening to reduce batter build-up on basket surfaces.

When frying is completed, remove baskets or product.  Hang baskets on rear basket hangers.
Remove food and season it.  Do not salt food over the shortening because salt could cause a
chemical change in the oil.

Fig. 4

Fig. 5

Summary of Contents for ML-136401













Reviews: