background image

THANK YOU for your purchase of this Vulcan Air Tool. With proper care and 

use you can expect your purchase to provide years of trouble free service!

SHOULD YOU HAVE A QUESTION OR A PROBLEM WITH YOUR 

VULCAN TOOL, PLEASE CALL OUR CUSTOMER SERVICE 

DEPARTMENT TOLL FREE AT:

1-800-482-0131

Please have the tool, model number and instruction manual at hand before calling.

ONE YEAR LIMITED CONSUMER WARRANTY

If you have a question or should you have a problem with any Vulcan Air Tool, call 

the Vulcan Customer Service line at 1-800-48-0131.

This product is warranted to be free from defects to material and workmanship 

for a period of ONE YEAR from date of purchase. If defective the product will be 

repaired or replaced. Call the Vulcan Power Tool customer service line at 1-800-

48-0131 and a customer representative will attempt to help resolve any issue. If 

directed by a representative, return the product along with proof of purchase to 

your dealer. Normal wear, damage due to abuse or mishandling or unauthorized 

repair is not covered. This warranty does not apply to accessories. This warranty 

gives you specific legal rights that vary from state to state.

This tool is intended for consumer use and is not a commercial tool. In the event 

the tool is used commercially, the warranty should be for a period of 30 days.

VULCAN AIR TOOLS ARE MADE EXCLUSIVELY FOR:

Memphis, TN  38101

Summary of Contents for 404-7791















Reviews: