Vulcan-Hart 244 627 Owner'S Manual And Installation Instructions Download Page 7

ABOUT YOUR WATER HEATER 

GENERAL MAINTENANCE 

The  jacket  of  the  water  heater  can  be  cleaned  with  a  soft  cloth  and  warm  mild  soapy  water.  Under  no 
circumstances should abrasive materials or powders be used. 
 
The  area  around  the  water  heater  can  be  sprayed  with  insecticide  to  rid  the  area  of  insects.  Insects 
encroaching into or nesting in the water heater can interfere with the operation of the water heater and also 
damage components. 
 

MINOR SIX MONTH MAINTENANCE 

It is recommended minor maintenance be performed every six months by the dwelling occupant. 
 
The minor maintenance includes: 

 

Inspect around the air inlet, flue terminal and the water heater in general for plant growth. 

 

Trim back any shrubs, bushes or other plants which have encroached around the water heater. 

Plant  growth  across  the  air  inlet  and  flue  terminal  can  interfere  with  the  performance  of  the  water 
heater. 

 

Inspect around the water heater for insect infestations, such as ants. 

 

Spray  insecticide around the water heater if necessary to rid the area of insects. Do not spray the 
surface or into the air inlet or flue terminal of the water heater. 

Insects encroaching into or nesting in the water heater can interfere with the operation of the water 
heater and also damage components. 

 

Check the drain line from the safe tray (if one is installed) is not blocked. 

 

MAJOR FIVE YEAR SERVICE 

For safe and efficient operation, it is recommended a five year service be conducted on the water heater. 
 

  Warning

:  Servicing  of  a  water  heater  must  only  be  carried  out  by  qualified  personnel.  Phone  Rheem 

Service or their nearest Accredited Service Agent. 
 

Note:

 The five year service and routine replacement of any components,  if required, are not included in the 

Vulcan  warranty.  A  charge  will  be  made  for  this  work.  Only  genuine  replacement  parts  should  be  used  on 
this water heater. 
 
The five year service includes the following actions: 

 

Check and if necessary adjust the gas pressure. 

 

Check the operation of and clean the burner. 

 

Visually check the unit for any potential problems. 

 

Inspect all connections. 

 

Check the drain line from the safe tray (if one is installed) is not blocked. 

 

Summary of Contents for 244 627

































Reviews: