background image

10 •   Vulcan Magnetic Upright Bike  | INSTRUCTION MANUAL

Troubleshooting Guide:

• 

Verify that all bolts and nuts are locked properly and the turning parts are free of damage and should be able to turn freely.

• 

Clean the equipment with soap and a slightly damp cloth only. Please do not use any solvents to clean the equipment.

PROBLEM

POTENTIAL CAUSES

CORRECTIONS

Base is unstable.

• 

Floor is not flat or there is small object 

under the front or rear stabilizer.

• 

The rear stabilizer end caps on the rear 

stabilizer have not been leveled when 

adjusting.

• 

Remove the object.

• 

Adjust the rear stabilizer end caps.

Handlebar or seat post 

is shaking.

• 

The bolt or round knob is loose.

• 

Tighten the bolt or round knob.

Loud noise from the 

moving parts.

• 

The interval of the parts is improper 

tighten.

• 

Open the covers to adjust.

No resistance when 

riding the upright bike.

• 

The interval of the magnetic resistance 

increases.

• 

Tension control knob is damaged.

• 

Belt slips.

• 

The bearing set is damaged. 

• 

Open the covers to adjust.

• 

Change the tension control knob.

• 

Open the covers to adjust.

• 

Change the bearing set.

TROUBLESHOOTING

Summary of Contents for 53040

















Reviews: