MAINTENANCE
This equipment complies with FCC AND IC REGULATIONS 15 and 68
of the Federal Communications Commission (FCC) rules for the United
States. It also complies with regulations RSS-210 and CS-03 of Industry
Canada (IC).
A label is located on the underside of the base unit containing either
the FCC registration number and Ringer Equivalence Number (REN)
or the IC registration number and Load Number. You must, upon request,
provide this information to your local telephone company.
This equipment is compatible with inductively coupled hearing aids.
FCC Part 15
Warning:Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of
the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet or on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Part 68
The FCC requires that you connect your cordless telephone to the
nationwide telephone network through a modular telephone jack (USOC
RJ11C or RJ11W).
Your telephone company may discontinue your service if your equipment
causes harm to the telephone network. They will notify you in advance
of disconnection, if possible. During notification, you will be informed
of your right to file a complaint with the FCC.
If it is determined that your telephone equipment is malfunctioning, the
FCC requires that it not be used and that it be unplugged from the
modular jack until the problem has been corrected. Repairs to this
telephone equipment can only be made by the manufacturer or its
authorized agents or by others who may be authorized by the FCC.
For repair procedures, follow the instructions outlined under the VTECH
Limited Warranty.
WARRANTY STATEMENT
TAKING CARE OF YOUR TELEPHONE.
Your VT
9110
cordless telephone contains
sophisticated electronic parts so it must be
treated with care.
Avoid rough treatment
Place the handset down gently. Save the
original packing materials to protect your
telephone if you ever need to ship it.
Avoid Water
Your telephone can be damaged if it gets wet.
Do not use the handset outdoors in the rain,
or handle it with wet hands. Do not install
your base unit near a sink, bathtub or shower.
Remember that electrical appliances can
cause serious injury if used when you are wet
or standing in water. If your base unit should
fall into water,
DO NOT RETRIEVE IT UNTIL
YOU UNPLUG THE POWER CORD AND
TELEPHONE LINE CORDS FROM THE
WALL. Then pull the unit out by the
unplugged cords.
Electrical Storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment.
For your own safety, use caution when using
electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing
that should retain its luster for many years.
Clean it only with a soft cloth slightly
dampened with water or a mild soap. Do not
use excess water or cleaning solvents of any
kind.
WHAT DOES OUR WARRANTY COVER?
•
Any defect in material or workmanship.
FOR HOW LONG AFTER THE ORIGINAL PURCHASE?
•
One Year.
WHAT WILL VTECH DO?
•
At our option, repair or replace your unit.
HOW DO I SEND MY UNIT, IN OR OUT OF WARRANTY?
•
Call VTECH Electronics customer service for Return Authorization at: 1-800-595-9511
•
Properly pack your unit. Include any cables & accessories which were originally provided with
the product. We recommend using the original carton and packing materials.
•
Include in the package a copy of the sales receipt or other evidence of date of original purchase
(if the unit was purchased within the last twelve months.)
•
Print your name and address, along with a description of the defect, and include this in the
package.
•
Include payment for any service or repair not covered by the warranty, as determined by VTECH
Communications.
•
In the US, ship the unit via UPS Insured, or equivalent to:
VTECH COMMUNICATIONS INC.
11035 SW 11th Street
Bldg. B Suite 270
Beaverton, OR 97005
VTECH Communications assumes no responsibility for units sent without prior Return Authorization.
WHAT DOES OUR WARRANTY NOT COVER?
•
Batteries
•
Damage from misuse, neglect, or acts of nature (lightning, floods, power surges. etc.)
•
Products which may have been modified or incorporated into other products
•
Products purchased outside the USA
•
Products serviced by the owner or a service facility not expressly authorized by VTECH
Communications
•
Products purchased more than 12 months from current date
HOW DOES STATE LAW RELATE TO THIS WARRANTY?
•
This warranty gives you specific rights. You may also have other rights which vary from state to
state.
IF YOU PURCHASED YOUR TELEPHONE IN CANADA
Please call:
1-800-267-7377 for return authorization.
Ship to:
VTECH ELECTRONICS LTD.
200-7671 ALDERBRIDGE WAY
RICHMOND, BC V6X 1Z9
FCC AND IC REGULATIONS
The REN is useful in determining the number of devices you may connect
to your telephone line and still enable the devices to ring when you
receive a call. The general rule is that the REN value should not exceed
5.0 total; however, contact your local telephone company for the specific
number in your area.
IC (Industry Canada)
This telephone is registered for use in Canada.
Notice:
The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network, protective, operational and
safety requirements. Industry Canada does not guarantee
the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible
to be connected to the facilities of the local telecommunications
company.The equipment must also be installed using an acceptable
method of connections. The customer should be aware that compliance
with the above conditions may not prevent degradation of service in
situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any repairs
or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Caution: Users should not attempt to make such connections
themselves, but should contact appropriate electric inspection
authority, or electrician, as appropriate.
Notice:
The REN assigned to this device denotes the number of
devices you may connect to the telephone loop which is used
by the device to prevent overloading.The termination on a
loop may consist of any combination of devices subjected
only to the requirement that the sum of the REN does not
exceed five(5.0).
This device complies with RSS-210 of Industry Canada. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
12
13
14
OPTIONAL HEADSET INSTALLATION &
OPERATING INSTRUCTIONS
Your VT
9110
cordless telephone is equipped with a 2.5mm Headset Jack for use with an
OPTIONAL
accessory Headset for hands-free operation.
If you choose to use the Headset option, you must do the following:
INSTALLATION
• Obtain an optional accessory Head set, which is compatible with
the VT
9110.
Please contact VTECH Communications Customer Service, in the
U.S. toll-free at 1-800-595-9511,in the Canada call 1-800-267-7377
for dealer information in your local area. You can also purchase a
compatible Headset directly from VTECH Communications Customer
Service.
• Once you have a compatible 2.5mm Headset, locate the Headset
Jack on the Handset of your VT
9110
. Connect the plug on the
Headset to the jack on the cordless Handset. The plug should fit
securely. Do not force the connection. See illustration.
OPERATION
NOTE: Whenever a compatible Headset is connected to the cordless Handset, the microphone
on the Handset will be MUTED. This is done to limit the effect of background noise.
•
The following operational characteristics apply to VTECH Headsets. the same may also apply
to other (non-VTECH) compatible headsets, but VTECH assumes no responsibility for their
performance.
•
The VTECH brand compatible Headset has a monaural design which is reversible, so you can
wear your Headset on either the left or right ear, leaving one ear free for room conversation.
•
For maximum sound quality, the flexible microphone should be
positioned at the corner of your mouth, about one inch from your
mouth.
BELT CLIP
•
The VT
9110
is also equipped with a detachable belt clip. Align the
pins on the inside edge of the belt clip with the notches on the side of
the VT
9110
handset. The belt clip should snap securely into place.
Do not force the connection. See Illustration.
TECHNICAL
SPECIFICATIONS
FREQUENCY CONTROL
Crystal Controlled Dual PLL Synthesizer
TRANSMIT FREQUENCY
Handset:
923.10 MHz to 927.75 MHz
Base:
902.3 MHz to 906.65 MHz
RECEIVE FREQUENCY
Handset:
902.3 MHz to 906.65 MHz
Base:
923.10 MHz to 927.75 MHz
NOMINAL EFFECTIVE RANGE
Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
SIZE
Handset:
17.5cm x 5.5cm x 3.9cm
(L x W xT) maximum
(antenna excluded)
Base:
19.3cm x 14.8cm x 5.4cm
(L x W x T) maximum
(antenna excluded)
WEIGHT
Handset:
146 grams
Base:
283 grams
POWER REQUIREMENTS
Handset:
Self-contained nickel-
cadmium rechargeable
battery supply, 3.6V nominal,
400mAh capacity.
Power Adapter: 9V DC @ 300mA
SPECIFICATIONS ARE TYPICAL AND
MAY CHANGE WITHOUT NOTICE.
15
